Search found 494 matches

by Donald Thomson
Wed, Dec 09 2015, 7:41PM
Forum: eCabinet Systems Software
Topic: Tenon cleanup
Replies: 9
Views: 4244

Re: Tenon cleanup

I have the same issues. All my tenons have to be cleaned up. Another problem is most of my tenons are cut about .0156" to long. So I have to take all my cabinet parts with tenons to the edge sander and sand them off so the parts fit properly. Yes, I have micrometer my bits and my material to th...
by Donald Thomson
Fri, Nov 13 2015, 1:42PM
Forum: eCabinet Systems Software
Topic: New maintenance relese
Replies: 0
Views: 5112

New maintenance relese

The new release I was prompted to install this morning seems so much faster.

Thank you Thermwood!!!! :D
by Donald Thomson
Mon, Nov 09 2015, 2:39PM
Forum: eCabinet Systems Software
Topic: LDE problem with latest upgrade
Replies: 4
Views: 2500

Re: LDE problem with latest upgrade

Rick,

How would the cabinet get slightly rotated? All I did was bring it in from CE and set Page Setup to landscape mode. Then resized the cabinet to fit in the page. Then hide all the parts I needed to to get to just the faceframe for measurements. Kinda confused on that.
by Donald Thomson
Mon, Nov 09 2015, 1:48PM
Forum: eCabinet Systems Software
Topic: LDE problem with latest upgrade
Replies: 4
Views: 2500

LDE problem with latest upgrade

Attached is an LDE rendering of a cabinet. Also attached is the cabinet hsf file.

Brought cabinet in from CE
Hide drawer faces and doors
Hide stretchers
Hide back of cabinet

Now there are all these extra lines and I don't know where they came from. It makes setting dimensions a bit difficult.
by Donald Thomson
Fri, Nov 06 2015, 12:36PM
Forum: eCabinet Systems Software
Topic: Update to 6.1 installed - now much slower
Replies: 0
Views: 4119

Update to 6.1 installed - now much slower

I was prompted to upgrade my 6.1 installation this morning. I installed the update. Now things are much slower running. Going from Drawer/Door editor back to main takes much longer to recalc everything then it did before. Saving a cabinet seems to take longer then it did before. The program seems mo...
by Donald Thomson
Fri, Nov 06 2015, 12:24PM
Forum: eCabinet Systems Software
Topic: Problems with 6.1
Replies: 8
Views: 2815

Re: Problems with 6.1

Rick,

Here is the Dropbox location of the file

https://www.dropbox.com/s/pwx4zpfqgmguu ... t.esj?dl=0
by Donald Thomson
Wed, Nov 04 2015, 8:29PM
Forum: eCabinet Systems Software
Topic: Problems with 6.1
Replies: 8
Views: 2815

Re: Problems with 6.1

I did ZIP it. 23.6MB zipped.
by Donald Thomson
Wed, Nov 04 2015, 5:46PM
Forum: eCabinet Systems Software
Topic: Problems with 6.1
Replies: 8
Views: 2815

Re: Problems with 6.1

Rick,

I keep getting an error when I email this project. It says

Error 552: DATA size exceeds the maximum permitted.

Don't think it's on my end because I've sent larger emails, then the one I'm trying to send to you, to other people.
by Donald Thomson
Wed, Nov 04 2015, 5:06PM
Forum: eCabinet Systems Software
Topic: Problems with 6.1
Replies: 8
Views: 2815

Re: Problems with 6.1

Rick,

I will ZIP the job and send it.
by Donald Thomson
Wed, Nov 04 2015, 3:03PM
Forum: eCabinet Systems Software
Topic: Problems with 6.1
Replies: 8
Views: 2815

Problems with 6.1

I loaded a job that worked perfectly in the beta and RC versions and saved it yesterday under the last RC version. I've nested it on multiple occasions, run cutlists and many other operations with no problem. Now I load the project into 6.1 and run a nesting operation and get the following error dia...
by Donald Thomson
Wed, Sep 02 2015, 3:06PM
Forum: eCabinet Systems Software
Topic: Countertop to Constraint Manager
Replies: 4
Views: 2099

Re: Countertop to Constraint Manager

Thank you Scott.

Any chance we might be able to get oval capability in PE or be able to use CM for countertops in a future release?
by Donald Thomson
Wed, Sep 02 2015, 1:34PM
Forum: eCabinet Systems Software
Topic: Countertop to Constraint Manager
Replies: 4
Views: 2099

Countertop to Constraint Manager

Is there a way to take a countertop into the constraint manager so I can turn circle cutouts into oval cutouts?

Trying to add oval sink cutouts in a vanity countertop.
by Donald Thomson
Fri, Aug 28 2015, 3:27PM
Forum: eCabinet Systems Software
Topic: Hiding a wall in presentation mode
Replies: 2
Views: 1098

Hiding a wall in presentation mode

I have done a kitchen layout. There is an island that has base cabinets and upper cabinets hanging from the ceiling above. I used a 1" thick wall to anchor the cabinets to. Now, I would like to hide that wall when in presentation mode so the client doesn't see it and sees things as they will ac...
by Donald Thomson
Thu, Aug 20 2015, 5:22PM
Forum: eCabinet Systems Software
Topic: Large Job Running Painfully Slow_Need Advice
Replies: 3
Views: 1577

Re: Large Job Running Painfully Slow_Need Advice

I have noticed this same behavior in larger jobs. Going from room layout to CE takes a long time. Then moving between the different editors takes a long time. I have noticed a lot of regeneration of all parts of a cabinet even if I made no changes in an editor. The slowest is cabinets that have a mu...
by Donald Thomson
Thu, Aug 20 2015, 2:04PM
Forum: eCabinet Systems Software
Topic: Changing drawer box depth
Replies: 7
Views: 1918

Re: Changing drawer box depth

Will the process you outline also work where I am putting slide out trays (Dbx's without drawer fronts) in the Drawer Box Editor? This is where I have many PE modifications to the slide out trays.

Go to advanced search