Search found 675 matches

by Scott Marshburn
Sun, Apr 15 2012, 11:20AM
Forum: Thermwood 3-Axis Machinery
Topic: Question about applyed carvings
Replies: 1
Views: 543

Question about applyed carvings

We have a request to do some applied carvings I downloaded the carving update for control nesting and am going to download the carving libraries do I have to install the libraries on the controller as well as ecab can I even install them in ecab (the applied carvings) I see the folder for inset carv...
by Scott Marshburn
Sat, Apr 14 2012, 5:16AM
Forum: eCabinet Systems Software
Topic: Corner Cabinet Back
Replies: 1
Views: 548

Re: Corner Cabinet Back

Are you cutting out your parts by hand if so you could change the corner gap to 0 and check miter 90 deg. Corner. This would give you plenty to cut the 45s you are after. I cant see any way to make the miters change and cant seem to extend the left and right backs in the correct direction to allow e...
by Scott Marshburn
Thu, Apr 12 2012, 6:13AM
Forum: eCabinet Systems Software
Topic: Door desighner question
Replies: 7
Views: 1677

Re: Door desighner question

Sorry guys I posted the last before actually giving it a try the display panel method will work without saving as an assembly but I will still have to apply any hardware holes manually
by Scott Marshburn
Thu, Apr 12 2012, 5:46AM
Forum: eCabinet Systems Software
Topic: Door desighner question
Replies: 7
Views: 1677

Re: Door desighner question

Thanks Rick that is what I will have to do but this method will not allow me to have the door actually on the cabinet without making it an assembly. I was hoping to avoid that by using a display door instead as all of the doors and drawer fronts for this job are made like the one I posted. Also any ...
by Scott Marshburn
Wed, Apr 11 2012, 6:23PM
Forum: Thermwood 3-Axis Machinery
Topic: CN:5.70 issue on waste board settings
Replies: 7
Views: 1403

Re: CN:5.70 issue on waste board settings

Not only should the waste board issue be addressed but also the cut through amount it would be nice to default these settings to all groups
by Scott Marshburn
Wed, Apr 11 2012, 5:53PM
Forum: eCabinet Systems Software
Topic: Problem With drawer box desighner?
Replies: 7
Views: 1576

Re: Problem With drawer box desighner?

Thanks Rick
by Scott Marshburn
Wed, Apr 11 2012, 5:51PM
Forum: eCabinet Systems Software
Topic: Door desighner question
Replies: 7
Views: 1677

Re: Door desighner question

Thanks Rick Four reply:
But I tried that and the Attached pix and hsf file is what I get.I guess what I am asking Is would it be possible to have a selection for no edge banding just as in the edge banding editor
by Scott Marshburn
Sun, Apr 08 2012, 9:23AM
Forum: eCabinet Systems Software
Topic: Door desighner question
Replies: 7
Views: 1677

Door desighner question

Is there any way to create a display door in door designer without the edge banding?
by Scott Marshburn
Sun, Apr 08 2012, 7:27AM
Forum: eCabinet Systems Software
Topic: How do I rabbit around an opening after a cutout?
Replies: 9
Views: 2315

Re: How do I rabbit around an opening after a cutout?

[quote="Steve Unruh"]Leo, I've tried that; that was the way I originally drew the cutouts and it works after a fashion. there are 3 rectangular openings that are approximately 8 X 14 two that are 12 X 14 and one that is 14 X 16 inches. It takes a long time to pocked that top quarter inch. ...
by Scott Marshburn
Fri, Apr 06 2012, 4:52AM
Forum: eCabinet Systems Software
Topic: Problem With drawer box desighner?
Replies: 7
Views: 1576

Re: Problem With drawer box desighner?

Kerry When you set the bottom front to a negitive inset with a full dado for the bottom the result is the drawer in the attached file
by Scott Marshburn
Thu, Apr 05 2012, 4:54PM
Forum: eCabinet Systems Software
Topic: Problem With drawer box desighner?
Replies: 7
Views: 1576

Re: Problem With drawer box desighner?

Kerry Did you make a dwar box as described in my post? All of the sholder settings are set to 0" But when you set the front insets to -3/8 and the bottom front inset to -3/4 with a full dado set for bottom the back of the bottom looks like it extents by the same amount less the thickness of the...
by Scott Marshburn
Thu, Apr 05 2012, 5:34AM
Forum: eCabinet Systems Software
Topic: Problem With drawer box desighner?
Replies: 7
Views: 1576

Problem With drawer box desighner?

Go to drawer box designer take a standard drawer box with a 1/4 bottom. Remove the front Left and right sides are butt joints to the back all insets are 0" Inset Bottom 3/4" Left and right sides flush Bottom Settings: Back bottom flush ,Front front flush. Left and right full dado. Dado dep...
by Scott Marshburn
Mon, Apr 02 2012, 4:42PM
Forum: eCabinet Systems Software
Topic: Problem with shape manager?
Replies: 3
Views: 582

Re: Problem with shape manager?

Thanks Kerry and Scott for your help once again. I sure am glad that I don’t have to use all of those line segments to cut these parts after all. It really slows down my computer and takes for ever to wright the code at the machine.
by Scott Marshburn
Mon, Apr 02 2012, 5:18AM
Forum: eCabinet Systems Software
Topic: Problem with shape manager?
Replies: 3
Views: 582

Problem with shape manager?

In shape manager draw a 3 point arc at 0,0_ 20 3/8,11/16_ 40 3/4,0
I get a straight line no arch.
Also get the same result when importing as dxf from draft sight
I can get the geometry that I am after by importing from sketchup but every thing is line segments
by Scott Marshburn
Fri, Mar 30 2012, 6:27PM
Forum: eCabinet Systems Software
Topic: Help With part editor cuts on deck
Replies: 3
Views: 673

Re: Help With part editor cuts on deck

Thanks Rick for the promp responce .I will make sure to make a note of that

Go to advanced search