Search found 82 matches
- Wed, Jun 13 2007, 10:40AM
- Forum: eCabinet Systems Software
- Topic: Doors - Buy or Build?
- Replies: 12
- Views: 11231
- Wed, Jun 13 2007, 4:48AM
- Forum: eCabinet Systems Software
- Topic: Doors - Buy or Build?
- Replies: 12
- Views: 11231
- Sun, Jun 10 2007, 6:03AM
- Forum: eCabinet Systems Software
- Topic: New User
- Replies: 8
- Views: 7745
- Sun, May 27 2007, 6:32AM
- Forum: eCabinet Systems Software
- Topic: Just a ? and a thought....
- Replies: 5
- Views: 5403
- Fri, May 25 2007, 5:16PM
- Forum: eCabinet Systems Software
- Topic: designing freestanding furniture?
- Replies: 17
- Views: 18085
- Thu, May 24 2007, 12:43PM
- Forum: Customer Images
- Topic: High patio table and bar stools
- Replies: 3
- Views: 8404
- Wed, May 23 2007, 6:23AM
- Forum: Customer Images
- Topic: High patio table and bar stools
- Replies: 3
- Views: 8404
High patio table and bar stools
This was done in ecabs, just approved by customer, starting it today.
- Fri, May 18 2007, 8:36AM
- Forum: eCabinet Systems Software
- Topic: Still in part editor
- Replies: 2
- Views: 2708
- Fri, May 18 2007, 7:57AM
- Forum: eCabinet Systems Software
- Topic: Still in part editor
- Replies: 2
- Views: 2708
Still in part editor
When trying to make contour cuts in the part editor it seems that I can only make cuts created with the circle tool. If I try to use an arc or line I get the message \"contour selected seems not to be a closed contour\". I've done everything I can think of to make sure the thing is closed but I ...
- Fri, May 18 2007, 6:54AM
- Forum: eCabinet Systems Software
- Topic: part editor stupid question
- Replies: 2
- Views: 2496
- Thu, May 17 2007, 6:28AM
- Forum: eCabinet Systems Software
- Topic: part editor stupid question
- Replies: 2
- Views: 2496
part editor stupid question
OK, I load a display board 4\" wide 36\"long 3/4\" thick. Take it to the part editor. Part is displayed in yellow vertically. I want to put a 1\" chamfer on the upper right corner. After selecting the chamfer tool I enter that i want a 1\" radius, I then select the right side and it is highlighted ...
- Thu, May 17 2007, 5:41AM
- Forum: eCabinet Systems Software
- Topic: How to Draw a Round Column?
- Replies: 4
- Views: 4268
Leo'
Thanks for the quick lesson. I use the program a lot but I never tried to make columns. Didn't feel I had time to get involved with a lot of tool making, geometry etc.. Well I just followed your directions and now I have a nice shiny steel pole. It only took a couple of minutes. I have no idea ...
Thanks for the quick lesson. I use the program a lot but I never tried to make columns. Didn't feel I had time to get involved with a lot of tool making, geometry etc.. Well I just followed your directions and now I have a nice shiny steel pole. It only took a couple of minutes. I have no idea ...
- Fri, May 11 2007, 6:21AM
- Forum: eCabinet Systems Software
- Topic: Help Please
- Replies: 5
- Views: 4681
- Wed, May 09 2007, 5:39AM
- Forum: eCabinet Systems Software
- Topic: Need advice from thermwood guys
- Replies: 2
- Views: 3133
Need advice from thermwood guys
What should I do. Some folks are having problems with build three. Is this just a small insignificant percentage? Should I hold off with build 3? Will the problems solved out weigh any new problems?
At least one member is recommending not performing the upgrade, what's your advice. My old boss used ...
At least one member is recommending not performing the upgrade, what's your advice. My old boss used ...
- Sat, Apr 07 2007, 6:04AM
- Forum: eCabinet Systems Software
- Topic: Starting a new design from scratch
- Replies: 1
- Views: 2558
Starting a new design from scratch
I am designing a tall table with some bar stools for chairs. I always hear that you start with a cabinet then delete un needed parts and build from there. My question is, is there any reason why I cannot just build the entire project from display boards and save as an assy.
Also does anyone know ...
Also does anyone know ...