Search found 68 matches

by Carmen Addamo
Tue, Dec 13 2016, 8:30PM
Forum: eCabinet Systems Software
Topic: Cutting a profile on the other edge
Replies: 4
Views: 1085

Re: Cutting a profile on the other edge

I'll post jpeg's of the cabinet and tool. I want to profile the piece on the right side of what would be a fireplace opening. The left side and top have been profiled.

Base Cut.jpg



Fireplace Surround.jpg
by Carmen Addamo
Tue, Dec 13 2016, 12:53PM
Forum: eCabinet Systems Software
Topic: Cutting a profile on the other edge
Replies: 4
Views: 1085

Cutting a profile on the other edge

I know I have done this before but cant seem to figure it out today. I have two stretchers, one left, one right. I cut a profile on the inside edge of the left stretcher. Now i need to cut same profile on the inside edge of the right stretcher but the tool profile i created in ecabs is not symetrica...
by Carmen Addamo
Mon, Aug 22 2016, 6:41AM
Forum: eCabinet Systems Software
Topic: Double door reveals
Replies: 6
Views: 1219

Re: Double door reveals

Forrest has a good solution. When I have the situation you describe I always just make the reveal settings so the reveal total is first calculated and then divide equally (divide by 3 in your double door case). This is so both doors are the same width and only their location on the cabinet is slight...
by Carmen Addamo
Thu, Jul 21 2016, 8:48PM
Forum: eCabinet Systems Software
Topic: Best way to handle the staircase opening from the attic to 2nd floor
Replies: 8
Views: 1389

Re: Best way to handle the staircase opening from the attic to 2nd floor

Scott Thank you for the suggestions. Your ideas definitely helped me elevate my designs.
by Carmen Addamo
Thu, Jul 21 2016, 3:40PM
Forum: eCabinet Systems Software
Topic: Best way to handle the staircase opening from the attic to 2nd floor
Replies: 8
Views: 1389

Best way to handle the staircase opening from the attic to 2nd floor

Turning an attic into bedroom with large number of built-ins, custom bed etc. How would you handle the floor opening/stairs. I can only think to create a railing/knee wall around the location of the openings. Use a display cube to simulate an opening in the floor??
by Carmen Addamo
Sun, Jul 10 2016, 11:51AM
Forum: eCabinet Systems Software
Topic: Cabinet Depth Problem
Replies: 8
Views: 1700

Re: Cabinet Depth Problem

Travis in construction settings in the right/left sides tabs. under "Construction" > Front. Choose the appropriate construction method. Full dado, blind dado etc. Then set your dado depth in construction parameters in those same tabs.
by Carmen Addamo
Sun, Jul 10 2016, 11:40AM
Forum: eCabinet Systems Software
Topic: Part editor on multiple sides of a cube?
Replies: 0
Views: 2663

Part editor on multiple sides of a cube?

In it's simplest form I have a display cube. I want to apply part editor cuts to the face and also to the top. Is there any way to do so. The project is a vanity with two towers. Between the towers sits an arched bridge (soffit). The bottom of the soffit will have a frame and panel effect. To create...
by Carmen Addamo
Tue, Apr 26 2016, 6:04AM
Forum: eCabinet Systems Software
Topic: Ecabs doesn't recognize mid stile once a cab is saved
Replies: 6
Views: 2892

Re: Ecabs doesn't recognize mid stile once a cab is saved

Rick, Sorry about the delay in posting this. If you take this cabinet and try and install a partition, and mid stile, you will first notice the mid stile does not connect to the bottom rail. I have a negative float for the deck to act as a door stop. Then try to install a door and you will see it do...
by Carmen Addamo
Tue, Apr 12 2016, 5:58AM
Forum: eCabinet Systems Software
Topic: Ecabs doesn't recognize mid stile once a cab is saved
Replies: 6
Views: 2892

Re: Ecabs doesn't recognize mid stile once a cab is saved

Rick, I'm sorry but I would need some instruction on how to post a file.
by Carmen Addamo
Sat, Apr 09 2016, 1:35PM
Forum: eCabinet Systems Software
Topic: Ecabs doesn't recognize mid stile once a cab is saved
Replies: 6
Views: 2892

Re: Ecabs doesn't recognize mid stile once a cab is saved

Kerry Thanks for the reply. You may be misunderstanding me or I you. What I was trying to say was once I created a single opening cabinet, no mid stiles, no partitions, and saved that cabinet I can no longer add a mid stile to the cabinet or even just a partition. The software views the original sin...
by Carmen Addamo
Fri, Apr 08 2016, 7:56PM
Forum: eCabinet Systems Software
Topic: Ecabs doesn't recognize mid stile once a cab is saved
Replies: 6
Views: 2892

Ecabs doesn't recognize mid stile once a cab is saved

I built a standard face frame double door cabinet and saved it to my library. I then tried to edit the cabinet by adding a few partitions and a mid stile. I go to door editor and ecabs does not recognize the mid stile and treats the openings as one single opening even though I get seprate openings i...
by Carmen Addamo
Sun, Apr 03 2016, 6:48PM
Forum: eCabinet Systems Software
Topic: Associations
Replies: 4
Views: 1754

Re: Associations

Kerry Thanks. Let me explain what I am trying to do and maybe you or someone else can suggest a good approach. I have a directory of kitchen cabinets. I also have a directory of wall fillers and end panel. The wall fillers/end panels are just cabinets with all parts removed except a right or left si...
by Carmen Addamo
Sun, Apr 03 2016, 1:17PM
Forum: eCabinet Systems Software
Topic: Associations
Replies: 4
Views: 1754

Associations

Guys is it possible to associate two cabinets to form an assembly. Associating display boards to a cabinet works but when trying to do same to two cabinets the associations tab is not active.
by Carmen Addamo
Wed, Mar 30 2016, 9:16AM
Forum: eCabinet Systems Software
Topic: Detached Toe, a cabinet, and Custom Layout
Replies: 7
Views: 2153

Re: Detached Toe, a cabinet, and Custom Layout

Gregg I'm new myself but will try to help. As Far as detached toe(s) I have always placed the cabinets first and then the toe. Associate the toe with necessary walls. Take a wall into elevation/wall view that the toe is associated with. Make sure in the placement option box you are in freestyle. Sel...

Go to advanced search