Search found 175 matches

by Clint Buechlein
Wed, Apr 18 2018, 7:32AM
Forum: Thermwood 3-Axis Machinery
Topic: priorities glitch
Replies: 1
Views: 32

Re: priorities glitch

I'm seeing the same thing here. We will get it listed, thank you.

-Clint-
by Clint Buechlein
Wed, Apr 18 2018, 7:26AM
Forum: eCabinet Systems Software
Topic: Suggestions on how to drill three sets of shelf pin holes
Replies: 7
Views: 85

Re: Suggestions on how to drill three sets of shelf pin holes

Closet project where it is necessary to drill three rows of holes. How do i set up for the center row (for adjustable hanging rod) at a specific distance from the front (or it could be referenced from the back) edge. I would also like to drill uprights that do not actualy contain adjustable shelves...
by Clint Buechlein
Mon, Apr 16 2018, 8:44AM
Forum: eCabinet Systems Software
Topic: Can't open current file after upgrade to 6.2.1
Replies: 2
Views: 69

Re: Can't open current file after upgrade to 6.2.1

Leo,

Can you post the job or email it to cabinets@thermwood.com?

-Clint-
by Clint Buechlein
Wed, Apr 04 2018, 1:09PM
Forum: eCabinet Systems Software
Topic: Dovetail drawer depth not resizing properly
Replies: 3
Views: 239

Re: Dovetail drawer depth not resizing properly

Forrest, I looked at it for a few minutes yesterday then got wrapped up in other stuff. The first time I resized it, I had the same issue you did. At least close to what you did. My display size was wrong versus actual measured and inputted size, but the numbers weren't the same. I had seen an issue...
by Clint Buechlein
Wed, Apr 04 2018, 7:20AM
Forum: Thermwood 3-Axis Machinery
Topic: Aspire export/import
Replies: 10
Views: 352

Re: Aspire export/import

Thanks for that Clint. I haven't tried any code editing yet. In fact, I was trying to steer away from even opening that book. But that is good advice because I was thinking I would be able to do it in the machine controller. Thanking you Mark You can edit the code at the controller, but the ideal s...
by Clint Buechlein
Tue, Apr 03 2018, 7:41AM
Forum: Thermwood 3-Axis Machinery
Topic: Aspire export/import
Replies: 10
Views: 352

Re: Aspire export/import

Also as a note the posts for Aspire can be edited in Notepad. There are relatively easy to understand once you look at some code you've posted. Just be sure to make a copy of the post before you edit it in the event you break it too badly :lol: .

-Clint-
by Clint Buechlein
Mon, Apr 02 2018, 9:17AM
Forum: Thermwood 3-Axis Machinery
Topic: Aspire export/import
Replies: 10
Views: 352

Re: Aspire export/import

Everything Dave said and a little more information. The post will be close for your machine, but it will get hung up at the beginning if you don't adjust the pop up pin output number. And remove the input call for pop up pins. Also there is no ZSHIFT in that post so you'll have to choose Machine Bed...
by Clint Buechlein
Tue, Mar 20 2018, 7:54AM
Forum: Thermwood 3-Axis Machinery
Topic: Drill Hole Issues
Replies: 5
Views: 336

Re: Drill Hole Issues

Rachel, For your first question regarding the 5mm drill, make sure the 5mm drill is in the operation list before the 3.18 mm cutter. In general your tools should be ordered from largest to smallest. Control Nesting starts at operation 1 in Tooling and checks to operation 50. As soon as the Control N...
by Clint Buechlein
Fri, Mar 16 2018, 8:01AM
Forum: Thermwood 3-Axis Machinery
Topic: Machining plam on 1 1/2'' thick pressboard
Replies: 2
Views: 170

Re: Machining plam on 1 1/2'' thick pressboard

As you read the response below, keep in mind I don't do a lot of cutting. I do some, but not nearly enough to be considered "production". My initial thought is the 250-300 ipm is too slow for a 1/2" bit. Going by Onsrud's chip load calculator located here http://www.onsrud.com/files/p...
by Clint Buechlein
Thu, Mar 15 2018, 2:26PM
Forum: eCabinet Systems Software
Topic: Backup my libary ?
Replies: 7
Views: 373

Re: Backup my libary ?

Do you happen to know if this includes the librarys i have made and downloaded ? or do i save those in another way? Thanks again i love this fourm and eCabs! It should. The Jobs, Tools, and Drawer Boxes can all be stored somewhere other than default so you have the option to set the location where ...
by Clint Buechlein
Thu, Mar 15 2018, 7:34AM
Forum: eCabinet Systems Software
Topic: Duplicating cabinets for better nesting.
Replies: 4
Views: 320

Re: Duplicating cabinets for better nesting.

Hi all, I am making seven kitchenettes and have created one of them (which comprises of three cabinets and a benctop). Is there any way that I can multiply that kitchenette by seven to get better nesting and less waste, or do I have to create it seven times in the same room to do so? Thanks--Mick. ...
by Clint Buechlein
Wed, Mar 14 2018, 12:38PM
Forum: eCabinet Systems Software
Topic: How to get version 6.2
Replies: 9
Views: 376

Re: How to get version 6.2

Andy, There shouldn't be any issues losing files or settings. If you haven't lately (or ever) taken a backup from eCabinets, I highly highly highly suggest you do. The backup will grab important files and settings in the event of a hard drive failure. I highly recommend creating the back up and stor...
by Clint Buechlein
Wed, Mar 14 2018, 7:25AM
Forum: eCabinet Systems Software
Topic: How to get version 6.2
Replies: 9
Views: 376

Re: How to get version 6.2

That is very possible. Most of the time my internet is amazing but today its really bad. I tried looking for the files to try them again and could not find them in that folder. do you have any suggestions on how to proceed from here? You'll have to start the download again. The download most likely...
by Clint Buechlein
Wed, Mar 14 2018, 7:22AM
Forum: Thermwood 3-Axis Machinery
Topic: Print Engine Error
Replies: 7
Views: 242

Re: Print Engine Error

Just out of curiosity I tried the export option at the machine and the desktop version. Both display the error. Never use export but there does seem to be a problem there. We are aware of the issue, just haven't made it there. The export option is Window's way of creating a PDF. There are other opt...

Go to advanced search