Search found 93 matches

by Chris B Campbell
Sat, Jul 30 2016, 12:03PM
Forum: eCabinet Systems Software
Topic: Back Shelf pin holes.
Replies: 4
Views: 4302

Back Shelf pin holes.

Hey All,
Wanting to use the back shelf pin hole feature with a partition, I can only get holes on the left side of the back??
Am I doing something wrong?

Thanks,
Chris
by Chris B Campbell
Sun, Jan 31 2016, 12:11PM
Forum: eCabinet Systems Software
Topic: Beaded face Frames
Replies: 0
Views: 5659

Beaded face Frames

Hey All, We have been doing a few beaded face frames using the Kreg jig. Actually works pretty good. What I would like to do is give the cut out/build sheets to the shop with dimensioned F/F centers, in other words I would like to give the shop the center of two mid rails so there's no mistake in we...
by Chris B Campbell
Wed, Oct 14 2015, 1:09PM
Forum: eCabinet Systems Software
Topic: nesting configuration
Replies: 7
Views: 4666

nesting configuration

Hey All,
Is it possible to get the smaller parts to the middle of the sheet? It seems when doing many parts (Drawer Boxes) The nest always ends up with the small parts at the outside edge were there is less vacuum and much more prone to moving. Yes we do the double pass.

Thanks,
Chris
by Chris B Campbell
Sat, Sep 12 2015, 1:58PM
Forum: eCabinet Systems Software
Topic: Countertop to Constraint Manager
Replies: 4
Views: 4487

Re: Countertop to Constraint Manager

Hi Scott,
Doing the same stuff here. I created the DXF file but how Do I load directly into the part editor Contour area?
I have a display panel in the Contour area but can not get the Ellipse to load?

Thanks,
Chris
by Chris B Campbell
Fri, Oct 10 2014, 5:22PM
Forum: eCabinet Systems Software
Topic: Drawer Front Grain Direction
Replies: 5
Views: 3847

Re: Drawer Front Grain Direction

LOL man I can't believe that was in there this whole time... A million thanks guys.

Chris
by Chris B Campbell
Fri, Oct 10 2014, 1:40PM
Forum: eCabinet Systems Software
Topic: Drawer Front Grain Direction
Replies: 5
Views: 3847

Re: Drawer Front Grain Direction

Thanks Guys,
Dennis when I install the drawer front you say I can rotate the grain direction? Not sure were that option is?

Thanks Again,
Chris
by Chris B Campbell
Thu, Oct 09 2014, 7:44AM
Forum: eCabinet Systems Software
Topic: Drawer Front Grain Direction
Replies: 5
Views: 3847

Drawer Front Grain Direction

Hey All, The new trend in Euro Cabinets seems to be having the grain of your doors and drawers run in the same direction and have matching grain running top to bottom (Vertical). I suppose I can build the cabinet and use display panels as fronts, kind of a PITA, but so far that is the only way I hav...
by Chris B Campbell
Sun, Jul 13 2014, 10:06AM
Forum: eCabinet Systems Software
Topic: louvered doors
Replies: 4
Views: 3814

Re: louvered doors

very cool Scott, I have yet to use all the tools, I really just don't have the time. I created a display door from the Conestoga CRP-10 with no panel then just stuck some display panels in there for louveres. PIA but it sort-a-worked. I don't know how your taking the display door into the part edito...
by Chris B Campbell
Thu, Jul 10 2014, 6:32PM
Forum: eCabinet Systems Software
Topic: louvered doors
Replies: 4
Views: 3814

louvered doors

hey all,
anyone have any good ideas for displaying a louvered door?

Thanks
Chris
by Chris B Campbell
Thu, Jul 10 2014, 1:14PM
Forum: eCabinet Systems Software
Topic: drawer Slide Pattern
Replies: 3
Views: 2894

Re: drawer Slide Pattern

No that would be a 5mm hole 3/8's into the material! Don't think a screw would hold that to well.. What I did was take the parts into part editor copied the hole pattern and reproduced there.

Thanks,,
Chris
by Chris B Campbell
Wed, Jul 09 2014, 6:56PM
Forum: eCabinet Systems Software
Topic: drawer Slide Pattern
Replies: 3
Views: 2894

drawer Slide Pattern

Hey Guys, I building some file cabinets Euro style stuff. So I had this idea for the drawer slides, there is only a 3/4" partition between the drawer boxes and then you have the right and left sides. I drilled the 5mm holes through the partition using the KV pattern in my hardware hole editor, ...
by Chris B Campbell
Wed, Feb 12 2014, 2:28PM
Forum: eCabinet Systems Software
Topic: Display cubes and part editor
Replies: 4
Views: 2223

Re: Display cubes and part editor

Thanks Scott,
Not gonna' even ask how, but I do appreciate the response :-)

have a great day,
Chris
by Chris B Campbell
Wed, Feb 12 2014, 8:14AM
Forum: eCabinet Systems Software
Topic: Display cubes and part editor
Replies: 4
Views: 2223

Display cubes and part editor

Hey All, Need some help I am trying to build a hood, three of the sides are angled (Front along with right & Left sides) . I can only display one side in the part editor to cut away the portion I need, for instance the front, I cannot however rotate the cube in the part editor so as to remove th...
by Chris B Campbell
Sun, Dec 15 2013, 2:50PM
Forum: eCabinet Systems Software
Topic: Building a radius wall
Replies: 2
Views: 1946

Re: Building a radius wall

Thanks Kerry,
Guess there's always a work-around :?

Chris
by Chris B Campbell
Thu, Dec 12 2013, 11:33AM
Forum: eCabinet Systems Software
Topic: Building a radius wall
Replies: 2
Views: 1946

Building a radius wall

Is it possible? I have a house that has radius cornered walls (22" R corners).

thanks,
Chris

Go to advanced search