Search found 90 matches

by Chris B Campbell
Thu, Nov 07 2013, 3:27PM
Forum: eCabinet Systems Software
Topic: Grain Direction
Replies: 2
Views: 1783

Grain Direction

hey All,

Is it possible to change the grain direction of a face frame made of sheet stock?? I want my rails to have vertical grain.

Thanks,
Chris
by Chris B Campbell
Tue, Jul 16 2013, 10:29AM
Forum: eCabinet Systems Software
Topic: Drawer Box Clamp?
Replies: 3
Views: 2919

Drawer Box Clamp?

Hey All, probably not the right forum but I could not find a better one ;-) Any of you guys that are building your own drawer boxes using a clamping system to assemble them. We are spending a ridiculous amount of time in the assembly stage. I was looking at clamping machines but not sure how well th...
by Chris B Campbell
Thu, Jul 04 2013, 9:52AM
Forum: eCabinet Systems Software
Topic: Angle the side of a FF cabinet
Replies: 2
Views: 1961

Re: Angle the side of a FF cabinet

Thanks Scott,
Pretty much what I thought... probably faster and easier with the table saw & Router.
by Chris B Campbell
Wed, Jul 03 2013, 7:34PM
Forum: eCabinet Systems Software
Topic: Angle the side of a FF cabinet
Replies: 2
Views: 1961

Angle the side of a FF cabinet

Is it possible to angle only one side of a cabinet? I have tried to put a 22.5* angle on the exposed right side of an upper cabinet, not having much luck.
Any help??

Thanks,
Chris
by Chris B Campbell
Fri, May 31 2013, 4:54PM
Forum: eCabinet Systems Software
Topic: drawer box finger joint
Replies: 0
Views: 2035

drawer box finger joint

We use the drawer box finger joint bit, I had Vortex sharpen so were do I measure this bit??
I am guessing it should be done at the very end of the tips width??


Thanks,
Chris
by Chris B Campbell
Tue, May 14 2013, 10:18AM
Forum: eCabinet Systems Software
Topic: Feature request
Replies: 2
Views: 1858

Re: Feature request

I think this for a different reason kind of address's my question about grain direction for a sheet cut (puzzle joint) Face frame construction. We are getting quite a few customers who are interested in cabinets that have ALL grain running in a vertical direction (Top, mid, and bottom rails included...
by Chris B Campbell
Sat, May 04 2013, 9:29AM
Forum: eCabinet Systems Software
Topic: change grain direction of face frame
Replies: 1
Views: 1252

change grain direction of face frame

Is it possible to change the grain direction of a sheet type face frame (top and bottom rails to have a vertical grain)

Thanks,
Chris
by Chris B Campbell
Fri, Feb 22 2013, 7:41PM
Forum: eCabinet Systems Software
Topic: raise the deck
Replies: 1
Views: 1254

raise the deck

hey All, I have some cabinets that are using inset doors, the customer would like for the 3/4" deck to be 1/4" above the 2" bottom rail so the door will have a stop. I thought it would be a simple change to the decks bottom inset of 1.25" to 1.5" but that does not work. Any ...
by Chris B Campbell
Tue, Jan 08 2013, 11:04AM
Forum: eCabinet Systems Software
Topic: Beaded face Frames
Replies: 2
Views: 3161

Beaded face Frames

Is there anyway to show beaded face frames with inset doors??

Thanks,
Chris
by Chris B Campbell
Sun, Dec 30 2012, 11:22AM
Forum: eCabinet Systems Software
Topic: End of Fly cut Code
Replies: 3
Views: 2195

Re: End of Fly cut Code

Hey Brian, yea I was a little concerned as I just don't have the experience with writing code. So I am looking at Ecab generated footers and working through my old class book. I have been running this same flycut that the Thermowood rep wrote for me years ago when I had the router installed. I shoul...
by Chris B Campbell
Sat, Dec 29 2012, 2:28PM
Forum: eCabinet Systems Software
Topic: End of Fly cut Code
Replies: 3
Views: 2195

End of Fly cut Code

hey All, Well I have put up with this for years now and i finally got the chance to fix it but I just need a little advice. My fly cut has always just gone "OUT OF BOUNDS" at the end of it's run, I have to emerg stop and reset to get it home. So now I would like it to return home as it sho...
by Chris B Campbell
Tue, Sep 11 2012, 4:00PM
Forum: eCabinet Systems Software
Topic: angled top
Replies: 5
Views: 3294

Re: angled top

Make your top a display panel. thats the only way I have been able to rotate cabinet parts.
by Chris B Campbell
Mon, Jun 18 2012, 9:32AM
Forum: eCabinet Systems Software
Topic: Cutting Aluminum
Replies: 3
Views: 2182

Re: Cutting Aluminum

LOL Yeah I will never forget the first time I cut a piece of aluminum on the table saw without a face shield! Ya learn fast... i dunno about the WD40 I have found that working my mill and running out of cutting fluid I had grabbed a can of WD40 used it and ruined the end mill... Just does not seem t...
by Chris B Campbell
Sun, Jun 17 2012, 12:51PM
Forum: eCabinet Systems Software
Topic: Cutting Aluminum
Replies: 3
Views: 2182

Cutting Aluminum

Not sure if this is the right place for this but... have any of you guys tried cutting aluminum sheet? maybe about .060" material. I use Bobcad software from time to time allowing me to easily create some nice stuff for the race car. Just been really hesitant about using the thermwood router as...
by Chris B Campbell
Mon, Jun 11 2012, 3:07PM
Forum: eCabinet Systems Software
Topic: drawer box front for pull-outs
Replies: 22
Views: 9505

Re: drawer box front for pull-outs

didn't see the last post.....
Thanks again,
Chris

Go to advanced search