Search found 113 matches

by Chris B Campbell
Fri, Feb 22 2013, 7:41PM
Forum: eCabinet Systems Software
Topic: raise the deck
Replies: 1
Views: 2945

raise the deck

hey All,
I have some cabinets that are using inset doors, the customer would like for the 3/4" deck to be 1/4" above the 2" bottom rail so the door will have a stop. I thought it would be a simple change to the decks bottom inset of 1.25" to 1.5" but that does not work. Any Ideas?
AAAAAAAAAAAAGH ...
by Chris B Campbell
Tue, Jan 08 2013, 11:04AM
Forum: eCabinet Systems Software
Topic: Beaded face Frames
Replies: 2
Views: 6781

Beaded face Frames

Is there anyway to show beaded face frames with inset doors??

Thanks,
Chris
by Chris B Campbell
Sun, Dec 30 2012, 11:22AM
Forum: eCabinet Systems Software
Topic: End of Fly cut Code
Replies: 3
Views: 6364

Re: End of Fly cut Code

Hey Brian,
yea I was a little concerned as I just don't have the experience with writing code. So I am looking at Ecab generated footers and working through my old class book. I have been running this same flycut that the Thermowood rep wrote for me years ago when I had the router installed. I ...
by Chris B Campbell
Sat, Dec 29 2012, 2:28PM
Forum: eCabinet Systems Software
Topic: End of Fly cut Code
Replies: 3
Views: 6364

End of Fly cut Code

hey All,
Well I have put up with this for years now and i finally got the chance to fix it but I just need a little advice. My fly cut has always just gone "OUT OF BOUNDS" at the end of it's run, I have to emerg stop and reset to get it home. So now I would like it to return home as it should ...
by Chris B Campbell
Tue, Sep 11 2012, 4:00PM
Forum: eCabinet Systems Software
Topic: angled top
Replies: 5
Views: 8016

Re: angled top

Make your top a display panel. thats the only way I have been able to rotate cabinet parts.
by Chris B Campbell
Mon, Jun 18 2012, 9:32AM
Forum: eCabinet Systems Software
Topic: Cutting Aluminum
Replies: 3
Views: 4908

Re: Cutting Aluminum

LOL Yeah I will never forget the first time I cut a piece of aluminum on the table saw without a face shield! Ya learn fast... i dunno about the WD40 I have found that working my mill and running out of cutting fluid I had grabbed a can of WD40 used it and ruined the end mill... Just does not seem ...
by Chris B Campbell
Sun, Jun 17 2012, 12:51PM
Forum: eCabinet Systems Software
Topic: Cutting Aluminum
Replies: 3
Views: 4908

Cutting Aluminum

Not sure if this is the right place for this but... have any of you guys tried cutting aluminum sheet? maybe about .060" material. I use Bobcad software from time to time allowing me to easily create some nice stuff for the race car. Just been really hesitant about using the thermwood router as a ...
by Chris B Campbell
Mon, Jun 11 2012, 3:07PM
Forum: eCabinet Systems Software
Topic: drawer box front for pull-outs
Replies: 22
Views: 27778

Re: drawer box front for pull-outs

didn't see the last post.....
Thanks again,
Chris
by Chris B Campbell
Mon, Jun 11 2012, 3:06PM
Forum: eCabinet Systems Software
Topic: drawer box front for pull-outs
Replies: 22
Views: 27778

Re: drawer box front for pull-outs

Seems to nest ok. I will run it later today. Don't understand why this changed? I am not sure if this was checked in the past??

Thanks,
Chris
by Chris B Campbell
Mon, Jun 11 2012, 2:30PM
Forum: eCabinet Systems Software
Topic: drawer box front for pull-outs
Replies: 22
Views: 27778

Re: drawer box front for pull-outs

Changed tool dia. to .25" Same problem.

Chris
by Chris B Campbell
Mon, Jun 11 2012, 1:37PM
Forum: eCabinet Systems Software
Topic: drawer box front for pull-outs
Replies: 22
Views: 27778

Re: drawer box front for pull-outs

Hi Joe,

I can try the bit dia. size soon, right now it is set at .235 with time left. as far as the arc dia. It's a 3 point arc. Radius of the arc... Well regrettably the line drawing editor doesn't recognize a drawer box to pull measurements off of.

Chris
by Chris B Campbell
Mon, Jun 11 2012, 11:50AM
Forum: eCabinet Systems Software
Topic: drawer box front for pull-outs
Replies: 22
Views: 27778

Re: drawer box front for pull-outs

Well it wont allow the .cab extension
by Chris B Campbell
Mon, Jun 11 2012, 11:49AM
Forum: eCabinet Systems Software
Topic: drawer box front for pull-outs
Replies: 22
Views: 27778

Re: drawer box front for pull-outs

$&*(^*)_(@#.... MONDAY MORNING!!!

Here Ya Go.
by Chris B Campbell
Mon, Jun 11 2012, 11:45AM
Forum: eCabinet Systems Software
Topic: drawer box front for pull-outs
Replies: 22
Views: 27778

Re: drawer box front for pull-outs

???? << Go to control nesting and load the twd you are having problem with. the go to file->Export>>>???
Okay, Load file, bottom of screen F5 (File) there is no export button? I can save a file (F2) but it is the CNC file.