Search found 93 matches

by Chris B Campbell
Sat, Mar 27 2010, 10:30AM
Forum: eCabinet Systems Software
Topic: build 3
Replies: 6
Views: 2659

Re: build 3

Tried again, used repair option, everything goes along as if it's all working fine, hit finish, open e-cabs get the "Verify" window hit verify, e-cabs opens and across the top I get "eCabinet System 6.0 Build 2 - Untitled".
So what the heck am I doing wrong!

Chris
by Chris B Campbell
Sat, Mar 27 2010, 10:20AM
Forum: eCabinet Systems Software
Topic: build 3
Replies: 6
Views: 2659

Re: build 3

XP Pro. No E cabs was not open... Thing is I have downloaded many other builds in V5 and 6 with no problem but for some reason I cannot get this build 3 to take?

Thanks again,
Chris
by Chris B Campbell
Fri, Mar 26 2010, 5:37PM
Forum: eCabinet Systems Software
Topic: build 3
Replies: 6
Views: 2659

build 3

Downloaded build 3 get options to Modify, Repair, or remove. tried modify then tried repair. Open e cab and still in Build 2. What am I missing? Do I need to completely remove?

Thanks,
Chris
by Chris B Campbell
Tue, Feb 09 2010, 3:47PM
Forum: eCabinet Systems Software
Topic: Define Hardware Problem
Replies: 3
Views: 1920

Define Hardware Problem

Working in the define hardware window I had created some slides. Made a few then needed to delete some... Highlighted line, clicked on "Remove Product" and it's gone. Close the define hardware window, re-open and my removed product is back? I tried to figure out were these self made produc...
by Chris B Campbell
Tue, Jan 26 2010, 7:13PM
Forum: eCabinet Systems Software
Topic: v6 is slower on my computer
Replies: 19
Views: 7455

Re: v6 is slower on my computer

Same slower than V5.2 problem as others. What I found becomes obvious, you really need to plan out the building of the cabinet, making doors, drawers, drawer box's and any part editor cuts the very last thing you do... Watching the computer re-generating each side of every drawer box every time you ...
by Chris B Campbell
Fri, Jan 22 2010, 11:11AM
Forum: eCabinet Systems Software
Topic: Problem with cost sheet
Replies: 11
Views: 4370

Problem with cost sheet

built 8 cabinets had them in an assembly checked $ amount got a whopping 104.00 Checked cut list all material is there,Checked my setting and preferences cost per sheet is ok. moved to batch, put in individual cabinets, nested, all sheets are there, cut list is correct... and still 104.00?? Any idea...
by Chris B Campbell
Wed, Jan 13 2010, 5:19PM
Forum: eCabinet Systems Software
Topic: get error when trying to save
Replies: 5
Views: 2517

Re: get error when trying to save

Tried to save as an Assembly and that worked.

Chris
by Chris B Campbell
Wed, Jan 13 2010, 5:15PM
Forum: eCabinet Systems Software
Topic: get error when trying to save
Replies: 5
Views: 2517

get error when trying to save

saved a cabinet in V6. Opened and placed 3/8" holes in the drawer box fronts tried to re-save but get the following error.
"An error occurred while adding HOOPS information to the save file"
Got a screen shot if you need it.

Chris Campbell
by Chris B Campbell
Wed, Jan 13 2010, 4:45PM
Forum: eCabinet Systems Software
Topic: Hinge & drawer slide hole patterns Gone?
Replies: 14
Views: 4670

Re: Hinge & drawer slide hole patterns Gone?

Thanks Scott, I tried adding hinges to a frameless base with a partition. Holes ok in the door but put my hinge plate holes in the partition? Is there something I am missing here? Tried a Std Base Framless from standard cab library single door put my dowel holes for the plate in the middle of the ca...
by Chris B Campbell
Wed, Jan 13 2010, 3:29PM
Forum: eCabinet Systems Software
Topic: Drw Boxes & Part Editor
Replies: 1
Views: 1376

Drw Boxes & Part Editor

It appears if you save a drawer box in the drawer box designer that you have made changes too using the part editor then use the saved box in a cabinet the P/Ed changes do not carry over to the newly dimensioned box, in other words if I create a drawer box with the cut-outs in the back for the under...
by Chris B Campbell
Wed, Jan 13 2010, 1:03PM
Forum: eCabinet Systems Software
Topic: Hinge & drawer slide hole patterns Gone?
Replies: 14
Views: 4670

Re: Hinge & drawer slide hole patterns Gone?

Thanks for the reply,
I did go there and my hole patterns are in the Patterns folder already and they match those in the V5 folder. Still I show 0 Hinges and slides.

Thanks again
Chris
by Chris B Campbell
Wed, Jan 13 2010, 12:20PM
Forum: eCabinet Systems Software
Topic: Hinge & drawer slide hole patterns Gone?
Replies: 14
Views: 4670

Hinge & drawer slide hole patterns Gone?

Hey all,
Downloaded V6 DID put in the user parts at download I have my materials and drawer/doors BUT NO Hole patterns for my slides or hinges that I previously had in V5.
Any help .

Thanks,
Chris Campbell
by Chris B Campbell
Mon, Jan 04 2010, 12:51PM
Forum: eCabinet Systems Software
Topic: Drawing an ellipse circle
Replies: 1
Views: 1265

Drawing an ellipse circle

Not sure if this is the right spot for this but… Does anyone know how I can draw a true ellipse circle using e cabs I don’t see any tool for this just the 3 point arch, circle and straight line. I need something about 18" wide X 26 Tall.

Thanks,
Chris
by Chris B Campbell
Thu, Dec 10 2009, 6:28PM
Forum: eCabinet Systems Software
Topic: transfering "My materials"
Replies: 1
Views: 1375

transfering "My materials"

Just got a new computer at home can anyone tell me how to transfer "My Materials" List from the shop to home using a memory stick.

Thanks

Chris
by Chris B Campbell
Thu, Oct 16 2008, 3:56PM
Forum: Design Sharing
Topic: What Would You Like to See in Design Sharing?
Replies: 55
Views: 65233

Re: What Would You Like to See in Design Sharing?

I'm not a heavy user of the forum so I am not sure this is the right spot for this request.
Has anyone built different fonts and numbers to be used for inset carvings?

Thanks
Chris

Go to advanced search