Search found 117 matches
- Sat, Nov 03 2007, 6:43AM
- Forum: eCabinet Systems Software
- Topic: Can't be too CAREFULL
- Replies: 8
- Views: 7833
Sorry to hear about your injuries guys.... I hate to admit that I did it too......even after the recent discussions about shop safety, and the pics of Dales terrible injury......about 5 weeks ago, I was making some small wooden drawer pulls on the router table. I was in a hurry, of course, not using ...
- Sat, Nov 03 2007, 5:56AM
- Forum: Customer Images
- Topic: Finished bar
- Replies: 7
- Views: 12184
Finished bar
These are the finished pics. I couldn't attach all the pics in one post.
Mike
Mike
- Sat, Nov 03 2007, 5:50AM
- Forum: Customer Images
- Topic: Basement bar design and finished project
- Replies: 0
- Views: 4749
Basement bar design and finished project
Well, almost finished.....the owner is hanging the bar lights himself and only had 1 hung when I took these pics. This is a mahagony bar in the basement of a lake house. Not seen is the pool table in front of the bar. I also did all of the paneling and trimwork for this job a few years ago. At that ...
- Sat, Nov 03 2007, 5:38AM
- Forum: Customer Images
- Topic: Wine Cabinets - Version 7...
- Replies: 14
- Views: 22544
- Thu, Nov 01 2007, 6:40PM
- Forum: Customer Images
- Topic: Wine Cabinets - Version 7...
- Replies: 14
- Views: 22544
Joe
Would you mind telling me how you drew the gridwork for the single bottles in the upper cabinets. I just built a wine cellar, actually phase one of a 3 part cellar, and because we were on a real tight schedule, I couldn't take the time to figure out how to draw the single bottle racks. I used ...
Would you mind telling me how you drew the gridwork for the single bottles in the upper cabinets. I just built a wine cellar, actually phase one of a 3 part cellar, and because we were on a real tight schedule, I couldn't take the time to figure out how to draw the single bottle racks. I used ...
- Sun, Oct 28 2007, 4:04PM
- Forum: eCabinet Systems Software
- Topic: RAW SEGMENT
- Replies: 12
- Views: 10550
- Sun, Oct 28 2007, 2:33PM
- Forum: eCabinet Systems Software
- Topic: RAW SEGMENT
- Replies: 12
- Views: 10550
I had the same problem about a year ago trying to bevel the edge on a right stile of a corner cabinet. The left stile was no problem, but I couldn't make the cut on the right stile. I brought it up on the forum, but I guess it never got noticed by the programers. Obviously, still not working...
Mike
Mike
- Tue, Oct 23 2007, 5:57PM
- Forum: eCabinet Systems Software
- Topic: Fasten the faceframes to the carcases
- Replies: 1
- Views: 2073
- Tue, Sep 25 2007, 5:01PM
- Forum: Customer Images
- Topic: maple vanity
- Replies: 14
- Views: 21982
- Sat, Sep 22 2007, 7:53AM
- Forum: eCabinet Systems Software
- Topic: Bean Drawers
- Replies: 4
- Views: 5127
Hey Brian
I havn't made any, but we had an island once that had bean drawers. The drawer front was typical 5 pc. with a plexiglass panel. The drawer sides were attached to the front with a half blind dovetail joint, the sides being inset 1/2\" to hide the slides. Approximately 1-1 1/4 inch behind ...
I havn't made any, but we had an island once that had bean drawers. The drawer front was typical 5 pc. with a plexiglass panel. The drawer sides were attached to the front with a half blind dovetail joint, the sides being inset 1/2\" to hide the slides. Approximately 1-1 1/4 inch behind ...
- Thu, Sep 06 2007, 6:36PM
- Forum: Customer Images
- Topic: Glazed Entertainment Center
- Replies: 13
- Views: 19466
- Sat, Sep 01 2007, 7:06AM
- Forum: Customer Images
- Topic: Glazed Entertainment Center
- Replies: 13
- Views: 19466
- Tue, Aug 28 2007, 7:34AM
- Forum: Customer Images
- Topic: Suspended Entertainment Center
- Replies: 1
- Views: 5143
- Mon, Aug 27 2007, 3:41AM
- Forum: Customer Images
- Topic: Wood images
- Replies: 2
- Views: 6292
- Tue, Aug 21 2007, 5:51PM
- Forum: eCabinet Systems Software
- Topic: Can't see numbers in detal room view
- Replies: 12
- Views: 10832