Search found 98 matches

by Terry Hall
Sat, Mar 26 2016, 10:21AM
Forum: eCabinet Systems Software
Topic: Common top and bottom rail between cabs
Replies: 21
Views: 4157

Re: Common top and bottom rail between cabs

Maybe I'm misunderstanding your meaning Scott, but I equalize and resize mine all the time using the construction method of running mid stiles to top and bottom rails, then adding mid rails. In my opinion the look is better and it makes for a more stable face frame. I have done it both ways over the...
by Terry Hall
Mon, Mar 21 2016, 9:55AM
Forum: eCabinet Systems Software
Topic: Common top and bottom rail between cabs
Replies: 21
Views: 4157

Re: Common top and bottom rail between cabs

This is an 84" island. I normally do one cabinet as long as I can get it in the house. You can install partitions if you've got say for instance drawer stacks on the outsides and a door in the middle.
by Terry Hall
Wed, Feb 17 2016, 3:49PM
Forum: eCabinet Systems Software
Topic: Face Frame/Cabinet Height Problem
Replies: 3
Views: 1322

Re: Face Frame/Cabinet Height Problem

As I recall Richard, you have to change the deck inset when you change the bottom rail width. Play with it a little bit and I believe that will solve your problem.
by Terry Hall
Tue, Dec 22 2015, 2:17PM
Forum: eCabinet Systems Software
Topic: How did I screw this up. Main job view reduced to 1/10
Replies: 3
Views: 2186

Re: How did I screw this up. Main job view reduced to 1/10

It seems to me that I had that happen once and as I recall I had placed a cabinet, or maybe another smaller object and it went way out into the perimeter outside the kitchen. Look around and see if you can find an object or something that you tried to place.
by Terry Hall
Fri, Aug 07 2015, 9:53AM
Forum: eCabinet Systems Software
Topic: "eCabinets has stopped working"
Replies: 1
Views: 1019

Re: "eCabinets has stopped working"

Wow, talk about a quick response! Thanks Scott and programmers, great job! Apparently, our laptop was somehow defaulting to the onboard video card rather than the high performance Nvidia card. Scott and the programmer (not certain what his name was, but really good) walked me thru setting up the sys...
by Terry Hall
Fri, Aug 07 2015, 8:58AM
Forum: eCabinet Systems Software
Topic: "eCabinets has stopped working"
Replies: 1
Views: 1019

"eCabinets has stopped working"

We installed Windows 10 on one of our desktops last week with no issues, just needed to generate a new reg code. We installed Windows 10 on our laptop and had to get a new reg code as well. When we put the new reg code in we got the message above "eCabinets has stopped working". We uninsta...
by Terry Hall
Fri, Jul 31 2015, 10:20AM
Forum: eCabinet Systems Software
Topic: Countertop
Replies: 9
Views: 2358

Re: Countertop

Try associating the ctop to the wall. Then pull up the wall view and set the ctop to the height of top of your cabinet. This happens to me once in a while as well.
by Terry Hall
Fri, Sep 05 2014, 1:52PM
Forum: eCabinet Systems Software
Topic: How Would You Draw This
Replies: 6
Views: 1511

Re: How Would You Draw This

Dennis, your sides are perfect and if I could turn the cabinet around, making the back the front and vice versa, add a face frame, drawers and doors it would work perfectly for me. Is there an easy way to reverse the cabinet? Thanks
by Terry Hall
Thu, Sep 04 2014, 2:13PM
Forum: eCabinet Systems Software
Topic: How Would You Draw This
Replies: 6
Views: 1511

Re: How Would You Draw This

Thanks Dennis, I'm going to work on it. I may look at the video sometime, but I've got three kitchens and this cabinet to do first. Thanks
by Terry Hall
Thu, Sep 04 2014, 8:33AM
Forum: eCabinet Systems Software
Topic: How Would You Draw This
Replies: 6
Views: 1511

Re: How Would You Draw This

Yes it is Brad, thank you.
by Terry Hall
Thu, Sep 04 2014, 8:14AM
Forum: eCabinet Systems Software
Topic: How Would You Draw This
Replies: 6
Views: 1511

How Would You Draw This

I can usually figure out how to draw some unusual pieces using Ecabs parts editor, however I can't seem to get this one. This is the side of a cabinet that will go under a stairway and I'd really like to figure out how to CNC it, cut the dadoes, etc. I do have Draftsite, but haven't actually used it...
by Terry Hall
Thu, Aug 07 2014, 7:05AM
Forum: eCabinet Systems Software
Topic: Odd Occurence(s)
Replies: 4
Views: 1296

Re: Odd Occurence(s)

Thanks Scott, I'll look at those things. I'm still curious though as to why this occurred without me making any changes to the software.
by Terry Hall
Sun, Aug 03 2014, 8:32AM
Forum: eCabinet Systems Software
Topic: Odd Occurence(s)
Replies: 4
Views: 1296

Re: Odd Occurence(s)

Thanks Forrest, like I said, I haven't tried it at the controller yet, this is a new occurrence at my design computer(s) though. I've always been able to design my cabinets with 96" sides and backs, then nest 96.5" material to be cut at 96", and nest my 96" to cut 95.5". Onc...
by Terry Hall
Sat, Aug 02 2014, 10:57AM
Forum: eCabinet Systems Software
Topic: Odd Occurence(s)
Replies: 4
Views: 1296

Odd Occurence(s)

I've been cutting sheet goods 96.5" x 49.5" and 96" x 48" respectively. I've always been able to nest the 96.5" material to 96" lengths and the 96" lengths to 95.5", never been a problem. Now however, in order to cut the 96" I have to change the size of t...
by Terry Hall
Mon, Jun 16 2014, 6:58AM
Forum: eCabinet Systems Software
Topic: Utilizing Some Offalls
Replies: 5
Views: 1298

Re: Utilizing Some Offalls

Thanks Scott M, I may give that a try as well.

Go to advanced search