Search found 397 matches

by Will Williamson
Wed, Feb 05 2014, 10:58AM
Forum: eCabinet Systems Software
Topic: Part editor trouble with DXF again
Replies: 27
Views: 4512

Re: Part editor trouble with DXF again

give me a call 810 310 1111
by Will Williamson
Wed, Feb 05 2014, 10:26AM
Forum: eCabinet Systems Software
Topic: Part editor trouble with DXF again
Replies: 27
Views: 4512

Re: Part editor trouble with DXF again

After 7 years and hundreds of hours struggling with dxf files, calling tech support, begging for help almost every job. A year and a half ago I bought a copy of Aspire and have not had to call tech support one time. Do yourself a favor. I hope I never have to go back to working with layered dxf files
by Will Williamson
Thu, Jan 23 2014, 1:58PM
Forum: Thermwood 3-Axis Machinery
Topic: Is there a way to estimate cut time for a job?
Replies: 4
Views: 1788

Re: Is there a way to estimate cut time for a job?

Aspire will do that. Based on the feeds and speeds then you can adjust to your particular machine.
by Will Williamson
Wed, Jan 15 2014, 8:44AM
Forum: Thermwood 3-Axis Machinery
Topic: shipping brackets
Replies: 3
Views: 1425

Re: shipping brackets

2 are used to bolt the control down to the table once you remove the spoil board you can see the threaded holes in the aluminum plate. the other is to keep the Spindle assembly in the home position
by Will Williamson
Thu, Dec 19 2013, 7:58PM
Forum: Thermwood 3-Axis Machinery
Topic: Vacuum Pump for my C53
Replies: 7
Views: 3199

Re: Vacuum Pump for my C53

I think the model 400 produces 400 cubic meters per hour. It is designed to pull a constant 22 inches of vacuum
by Will Williamson
Tue, Nov 12 2013, 8:01PM
Forum: Thermwood 3-Axis Machinery
Topic: Vacuum Pump for my C53
Replies: 7
Views: 3199

Re: Vacuum Pump for my C53

It is a model 400.
by Will Williamson
Wed, Nov 06 2013, 10:37AM
Forum: Thermwood 3-Axis Machinery
Topic: Vacuum Pump for my C53
Replies: 7
Views: 3199

Re: Vacuum Pump for my C53

I am still running the 18 HP Becker that Thermwood supplied with my CS45 5' x 10' seven years ago. Never had any problems in 7 years, not one
by Will Williamson
Thu, Sep 19 2013, 4:36PM
Forum: Thermwood 3-Axis Machinery
Topic: Suggested Profile Modeler Settings for Trim?
Replies: 1
Views: 932

Re: Suggested Profile Modeler Settings for Trim?

I always use the largest diameter tool that will fit the profile. To rough with the 3/8 ball I usually step over 1/2 the dia and step down 1/2 the Dia. at 500 IPM and finish with the 1/4 " use .02 or.03 stepover at 400 ipm on those small profiles you have I would be running from 3 to 4 hundred ...
by Will Williamson
Mon, Jul 15 2013, 8:52AM
Forum: Thermwood 3-Axis Machinery
Topic: Flip op miscutting
Replies: 10
Views: 2837

Re: Flip op miscutting

Can we post dxf files on here?
Daniel I keep a roll of clear packing tape handy and when ever I have an issue with warped material I run a piece of tape around the edge of the sheet 99.9 percent success rate
by Will Williamson
Sun, Jul 14 2013, 8:37AM
Forum: Thermwood 3-Axis Machinery
Topic: Flip op miscutting
Replies: 10
Views: 2837

Re: Flip op miscutting

Two sided cutting is when I locate dowels in my first side then mirror then flip the part in the software and drill my location dowel into the bed of of my machine but that does not have any thing to do with doing flip op in ecabinets I went through the same thing the last time ai set up for cabinet...
by Will Williamson
Sun, Jul 14 2013, 7:50AM
Forum: Thermwood 3-Axis Machinery
Topic: Flip op miscutting
Replies: 10
Views: 2837

Re: Flip op miscutting

Yes I use the sane same fixture offset for both . I make a small cabinet 12 x 12 x 12 and use it to set up and test my results i also make my own flip op fence 24" x 72" to locate to locate full sheets and on the inside corner of the jig where the fixture offset is I locate a drill operati...
by Will Williamson
Sat, Jul 13 2013, 2:09PM
Forum: Thermwood 3-Axis Machinery
Topic: Flip op miscutting
Replies: 10
Views: 2837

Re: Flip op miscutting

This is the kind of thing that only happens on the week end.
Go in there and make the necessary .125 adjustment to the axis G52 location and give it a try .
by Will Williamson
Sun, Jul 07 2013, 11:11AM
Forum: eCabinet Systems Software
Topic: Factors affecting fit and depth clearances
Replies: 15
Views: 3116

Re: Factors affecting fit and depth clearances

Design your self a small cabinet 12" x 12" x 12" and see for your self the result of your setting changes and flip ops
by Will Williamson
Fri, Jun 14 2013, 11:34AM
Forum: Thermwood 3-Axis Machinery
Topic: Drill Bank Plunge rate
Replies: 10
Views: 4570

Re: Drill Bank Plunge rate

Have you spoke to your tooling supplier? Call Vortex 715 355 7707
by Will Williamson
Mon, May 20 2013, 1:56PM
Forum: eCabinet Systems Software
Topic: Buying a new PC
Replies: 7
Views: 1759

Re: Buying a new PC

At the encouragement of my tech support ,3 months ago I bought a used 3 year old Dell Precision Laptop on craigs list for $200 dollars duo core Win 7 64 bit good grafix card It works fantastic. I bought it for a backup it is my second one I bought like that.

Go to advanced search