Search found 115 matches
- Mon, Oct 20 2008, 5:36PM
- Forum: eCabinet Systems Software
- Topic: Whisper Ride TV Lift
- Replies: 5
- Views: 4968
Re: Whisper Ride TV Lift
Thanks, George....I'm screwed up enough, and nuts already
- Mon, Oct 20 2008, 2:14PM
- Forum: eCabinet Systems Software
- Topic: Cabinet top with a door in it ?
- Replies: 7
- Views: 5513
Re: Cabinet top with a door in it ?
Thank you very much for the pics and cab files, George. I guess I still don't understand uploading/downloading usable files. The files are there but I can't quite figure out where to put them so that they open properly with eCab. I better go back to the how-to instructions... BTW the one you made up...
- Sun, Oct 19 2008, 7:58PM
- Forum: eCabinet Systems Software
- Topic: Cabinet top with a door in it ?
- Replies: 7
- Views: 5513
Re: Cabinet top with a door in it ?
Yes,George, that's pretty much what I'm trying to do. I finally used a modified FF for the top - only way I could figure to place a "door" in it. And my cabinet isn't deep enough for equip in front (your drop-down drawer front), so I put in a separator panel (using Kerry's up-down stretche...
- Sat, Oct 18 2008, 7:08PM
- Forum: eCabinet Systems Software
- Topic: How to add a left-right partition?
- Replies: 5
- Views: 4063
Re: How to add a left-right partition?
Thanks once again, Kerry. That worked just like you said. I wasn't thinking about using the stretcher up-down - need to think "outside the box" more often. I did have one problem, though. I had to take off my made-up face-frame top and put on a "real" top to define the top end of...
- Sat, Oct 18 2008, 1:16PM
- Forum: eCabinet Systems Software
- Topic: Cabinet top with a door in it ?
- Replies: 7
- Views: 5513
Cabinet top with a door in it ?
Need to place a hinged panel in a cabinet top for a pop-up. Essentially an inset flat door cut into the middle of the top. Suggestions on how to do it / show it in eCab ? Be nice if the door/panel could be rotated for display purposes..... In this one the opening needs to start 3/4" off the bac...
- Sat, Oct 18 2008, 1:10PM
- Forum: eCabinet Systems Software
- Topic: OK now what
- Replies: 8
- Views: 5465
Re: OK now what
Gary I think you have to "Batch" the cabinets into a job then create the cutlist from the batch. Especially if you used two copies of the same cabinet to set up the room
- Sat, Oct 18 2008, 12:21PM
- Forum: eCabinet Systems Software
- Topic: How to add a left-right partition?
- Replies: 5
- Views: 4063
Re: How to add a left-right partition?
Thanks, Kerry. Using a stretcher worked to get the panel in place. I wanted to keep it inset from the left and right end panels, to allow for the pocket slides and doors to go past it - can I make cutouts in the sides of the "stretcher" with the part editor? If I slice a couple of inches o...
- Fri, Oct 17 2008, 7:14PM
- Forum: eCabinet Systems Software
- Topic: How to add a left-right partition?
- Replies: 5
- Views: 4063
How to add a left-right partition?
I want to add a left-right partition aprox midway between the front and back, to create a sort of "false back" closing off a rear compartment. I already used the "Back" to close the real back of the cabinet, so I can't use it with a big inset. :? This is for a pop-up TV cabinet; ...
- Fri, Oct 10 2008, 12:22PM
- Forum: eCabinet Systems Software
- Topic: OT Molding search
- Replies: 20
- Views: 13321
Re: OT Molding search
Peter, as you have ordered from Walzcraft they will presumably send you the full catalog and color brochure. (If they don't, ask for them) :beer: You will be amazed at the stuff they have. Makes Conestoga look silly (at least based on what's linked to eCab) Too bad they won't do a deal thru eCab, bu...
- Fri, Oct 10 2008, 12:16PM
- Forum: eCabinet Systems Software
- Topic: French Speaking Members?
- Replies: 22
- Views: 15453
Re: French Speaking Members?
More simply than that, Dan, it means you are willing to LOOK for an answer and not take the "not my job" attitude.
I join the others in thanking you , and respecting you, for that.
I join the others in thanking you , and respecting you, for that.
- Wed, Oct 08 2008, 3:32PM
- Forum: eCabinet Systems Software
- Topic: French Speaking Members?
- Replies: 22
- Views: 15453
Re: French Speaking Members?
Hey, Dan, maybe you could link your translator to an image-processor and have your avatar morph, too......
- Mon, Oct 06 2008, 11:33AM
- Forum: eCabinet Systems Software
- Topic: Drawer head sizing
- Replies: 3
- Views: 3416
Re: Drawer head sizing
Todd The fixed shelf did it for me. I needed it there in order to place the partition between the two drawers, which I need because I'm using side-mount drawer slides. And this is a furniture cabinet base in a TV wall group, so I usually like to have some sort of separator or dust panel there anyway...
- Thu, Oct 02 2008, 11:13AM
- Forum: Customer 3D Files
- Topic: Bar
- Replies: 2
- Views: 5505
Re: Bar
OK, George: what came first, the real one or your e-Cab jpg ?
From the amount of stuff you post, doing eCab renderings must be your primary occupation .
From the amount of stuff you post, doing eCab renderings must be your primary occupation .
- Thu, Oct 02 2008, 11:07AM
- Forum: eCabinet Systems Software
- Topic: Add a partition in a drawer opening?
- Replies: 3
- Views: 3002
Re: Add a partition in a drawer opening?
Exactly right, Damon. Seems the process of defining the question and reading it spotlights the problem. It really DID feel like a litebulb going on....I could almst see the (!) there.
- Thu, Oct 02 2008, 11:01AM
- Forum: eCabinet Systems Software
- Topic: Vista Ultimate
- Replies: 25
- Views: 18418
Re: Vista Ultimate
Dan may be on the right track, based on this excerpt from an independent online Windows newsletter I subscribe to; Quote On our inaugural 64-bit Vista machine, our line-of-business applications and printers were deployed without a hitch. The trick for us was to open the System Configuration utility ...