Search found 92 matches
- Wed, May 14 2008, 3:58PM
- Forum: eCabinet Systems Software
- Topic: Tool creation
- Replies: 2
- Views: 2279
Tool creation
Hello everyone, I am very new in e-cabinets. I have been reading the posts. Here is my question. When I create a tool, what would I use it for in the program? The only thing that I can figure is moldings. If so... how do I work it out to make my moldings. The reason that I am asking is because I hav...
- Mon, May 12 2008, 10:18AM
- Forum: eCabinet Systems Software
- Topic: Mortise/Tenton in face frames.
- Replies: 2
- Views: 2178
Re: Mortise/Tenton in face frames.
Walker,
Thank you very much for the tip. I couldn't figure out what was going on.
Thank you very much for the tip. I couldn't figure out what was going on.
- Mon, May 12 2008, 8:37AM
- Forum: eCabinet Systems Software
- Topic: Mortise/Tenton in face frames.
- Replies: 2
- Views: 2178
Mortise/Tenton in face frames.
Hello Everyone,
Please check this cabinet out. I have been working on it and I have not been able to make the face frames m/t. I fix it and next thing I now it is back to butt joint.
I must be doing something wrong or there is something else going on that I do not know about.
Thanks!
Please check this cabinet out. I have been working on it and I have not been able to make the face frames m/t. I fix it and next thing I now it is back to butt joint.
I must be doing something wrong or there is something else going on that I do not know about.
Thanks!
- Sat, May 10 2008, 8:24PM
- Forum: eCabinet Systems Software
- Topic: DRAWER BOX ERROR
- Replies: 10
- Views: 6949
Re: DRAWER BOX ERROR
Rick,
I appreciated. I am not sure what I did there for a few minutes.
Thank you!
I appreciated. I am not sure what I did there for a few minutes.
Thank you!
- Sat, May 10 2008, 8:22PM
- Forum: eCabinet Systems Software
- Topic: Cabinet Moldings
- Replies: 3
- Views: 3438
Re: Cabinet Moldings
Thanks George, Those picture are great. I like the idea of using the modling editor, because if you have to change the size of the cabinet the molding changes size as well. Will that be a problem if you have molding for individual cabinets? In other words would that mess it up all this single moldin...
- Fri, May 09 2008, 4:27PM
- Forum: eCabinet Systems Software
- Topic: Floor extends past walls
- Replies: 7
- Views: 4744
Re: Floor extends past walls
Rick,
It seams like you had a bigger room; then you made a smaller room. It has happened with me many times, for some reason the software doesn't register what is going on.
I would delete the whole job and start all over again.
It seams like you had a bigger room; then you made a smaller room. It has happened with me many times, for some reason the software doesn't register what is going on.
I would delete the whole job and start all over again.
- Fri, May 09 2008, 2:27PM
- Forum: eCabinet Systems Software
- Topic: Cabinet Moldings
- Replies: 3
- Views: 3438
Cabinet Moldings
Hello everyone, I am working on my first really fancy kitchen layout. I have encountered some problems in placing moldings. What is the best way to do that? Would you install molding in the cabinet editor, even if there are just on the side of the cabinet? Or would you install molding after the cabi...
- Fri, May 09 2008, 12:23PM
- Forum: eCabinet Systems Software
- Topic: Wall Cabinet
- Replies: 5
- Views: 4293
Re: Wall Cabinet
Hello Dan,
How can you avoid that?
How can you avoid that?
- Fri, May 09 2008, 10:45AM
- Forum: eCabinet Systems Software
- Topic: DRAWER BOX ERROR
- Replies: 10
- Views: 6949
Re: DRAWER BOX ERROR
Thanks,
Here it is.
Let me know the outcome on that.
Thanks again!
Here it is.
Let me know the outcome on that.
Thanks again!
- Fri, May 09 2008, 10:27AM
- Forum: eCabinet Systems Software
- Topic: DRAWER BOX ERROR
- Replies: 10
- Views: 6949
Re: DRAWER BOX ERROR
Hey Walter,
Speaking of drawer box. When I place a drawer base cabinet and I have to resize, the drawer box does not resize with it. Is there something that I can do, or is there something that I am not doing?
Thanks!
Speaking of drawer box. When I place a drawer base cabinet and I have to resize, the drawer box does not resize with it. Is there something that I can do, or is there something that I am not doing?
Thanks!
- Fri, May 09 2008, 10:18AM
- Forum: eCabinet Systems Software
- Topic: Version 5.2 build 1
- Replies: 3
- Views: 2777
Re: Version 5.2 build 1
Todd, Thank you very much for your quick reply. Here is the cabinet. I am thinking it is for all the cabinets that I have installed, because I used the same material for all of them. The material name that I orginally used was 1/2"Ply_cabinext; which is 1/2" plywood. However, ever since se...
- Fri, May 09 2008, 9:49AM
- Forum: eCabinet Systems Software
- Topic: Version 5.2 build 1
- Replies: 3
- Views: 2777
Version 5.2 build 1
Hello everyone, I am having problems ever since I installed version 5.2 with my materials. Every time I try to open a job, or even when I take a cabinet to the cabinet editor, it keeps telling me that the material does not exist and I need create it. I have create the same material probably 5 or 6 t...
- Thu, May 08 2008, 4:20PM
- Forum: eCabinet Systems Software
- Topic: Positioning water pipe
- Replies: 3
- Views: 3310
Re: Positioning water pipe
Hey Mike,
Try out in a different job. Sometimes my computer acts crazy for somethings and I just need start all over again.
Try out in a different job. Sometimes my computer acts crazy for somethings and I just need start all over again.
- Tue, May 06 2008, 9:52AM
- Forum: eCabinet Systems Software
- Topic: Cabinet settings
- Replies: 1
- Views: 1910
Cabinet settings
Hello You'll, I have worked in several different cabinets and I have come to a conclusion that it must have a better way to do this. When I work on a base cabinet, I set everything such as doors, drawer, face frames, etc. Switching from base to base is not a problem, but when I pick a wall cabinet, ...
- Tue, May 06 2008, 9:47AM
- Forum: eCabinet Systems Software
- Topic: Face frame's
- Replies: 7
- Views: 4902
Re: Face frame's
Hey Dan, No, I am actually referring when I am building the cabinet. Right now I am working on a drawer base. I am working in the main area of the cabinet editor, I open constructions settings and fix several parts of my cabinets; back, deck, sides, etc; there I try to fix the face frame an that whe...