Search found 296 matches
- Tue, Mar 27 2007, 2:59PM
- Forum: eCabinet Systems Software
- Topic: Line bore patterns for 32mm / Zargen slides
- Replies: 5
- Views: 4693
another option to solve this... and this is what we do since i still can't convince them to change the set-up on the point-to-point to match the thermwood... is to create your holes the hard way in part editor. take your gable in and create a bunch of 5 mm holes, then take it to constraints manager ...
- Fri, Mar 23 2007, 9:25AM
- Forum: eCabinet Systems Software
- Topic: Deleting all parts except door
- Replies: 9
- Views: 6529
- Thu, Mar 22 2007, 10:36AM
- Forum: eCabinet Systems Software
- Topic: geometry creation after profile cuts?
- Replies: 3
- Views: 3304
geometry creation after profile cuts?
k, trying to make a shaker style mdf door... recessed panel, but with a profile around the inside of the frame. i created my profile tool, applied it to a rectangle, but now when i try to go and create the recessed panel with a pocket, i get an error message saying that i cannot create geometry on a...
- Thu, Mar 22 2007, 9:03AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Control Nesting: Odd Drilling Order
- Replies: 5
- Views: 4821
here is a job i am running right now. if you go to sheet 24 and 25 which are full of upper gables, it will drill all the 5mm holes fine, but will then drill 1 8mm hole at the top and bottom of each gable before returning to drill the rest of the holes around them. it certainly is not drilling them i...
- Thu, Mar 22 2007, 7:10AM
- Forum: eCabinet Systems Software
- Topic: crashes when changing material
- Replies: 8
- Views: 5415
i think that the last thing i did before saving it was adding the constraints to the top and to the lower shelf... and it saved fine. didn't try to change materials or anything at that time though. it was when i re-opened it, and ever since then, that the crashes have happened. as it is now, i have ...
- Thu, Mar 22 2007, 6:15AM
- Forum: eCabinet Systems Software
- Topic: crashes when changing material
- Replies: 8
- Views: 5415
so... it crashes on me when i go into construction settings and then hit ok in the cabinet editor. it also crashes if i try to enter the edge-banding area. it also crashes if i try to change sheet stock in the batch editor. it also crashes if i enter the construction settings from within the shelf/p...
- Wed, Mar 21 2007, 2:54PM
- Forum: eCabinet Systems Software
- Topic: crashes when changing material
- Replies: 8
- Views: 5415
crashes when changing material
just finished putting together a cabinet when i was informed that the material of some parts had to change. but when i go in to change the material, ecabs crashes right out as soon as i hit the OK button. can anybody figure out why or tell me how to get around this problem? her is the cabinet i am t...
- Wed, Mar 21 2007, 8:58AM
- Forum: eCabinet Systems Software
- Topic: trying to figure out doors
- Replies: 1
- Views: 1844
trying to figure out doors
k, be patient with me... so far, all we have done with ecabs is create cabinets and run batch jobs, and it works well and we have been pumping out up to around 20 kitchens a week at times this way. i don't have to worry about desing, just converting what the designers give me into real cabinets. we ...
- Tue, Mar 20 2007, 6:02AM
- Forum: Thermwood 3-Axis Machinery
- Topic: ATC issues
- Replies: 10
- Views: 8719
another thing to check would be your air pressures at each guage at the back of the gantry. i know that in our shop, we have had guys in for the past couple of weeks upgrading our compressed air lines and all sorts of other stuff, and i have had to tweak my pressure settings a couple of times to put...
- Mon, Mar 19 2007, 6:23AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Control Nesting: Odd Drilling Order
- Replies: 5
- Views: 4821
- Mon, Mar 19 2007, 6:21AM
- Forum: Thermwood 3-Axis Machinery
- Topic: ATC issues
- Replies: 10
- Views: 8719
- Wed, Mar 07 2007, 7:19AM
- Forum: eCabinet Systems Software
- Topic: New feature idea for the next version. \"Does it fit?\&
- Replies: 11
- Views: 8512
- Wed, Mar 07 2007, 7:17AM
- Forum: Thermwood 3-Axis Machinery
- Topic: DXF
- Replies: 12
- Views: 9511
- Tue, Mar 06 2007, 1:23PM
- Forum: eCabinet Systems Software
- Topic: New feature idea for the next version. \"Does it fit?\&
- Replies: 11
- Views: 8512
i would appreciate this kind of software... since i have built cabinets that won't fit up a flight of stairs and had to be broken apart and re-assembled/repaired at the top... sigh... :oops: the only problem i could foresee would be that you would end up spending more time plugging in building dimen...
- Sat, Mar 03 2007, 7:09AM
- Forum: eCabinet Systems Software
- Topic: 100 questions so many more to go.....
- Replies: 11
- Views: 7496