Hi Nat,
What did you figure out on your a on the RTA fittings.
I saw your video on You Tube nice set up. What type of vacuum pump or hold down system do you use.
Search found 39 matches
- Wed, Jun 03 2009, 4:53PM
- Forum: eCabinet Systems Software
- Topic: Assembly Screw Holes
- Replies: 2
- Views: 2754
- Mon, Jun 01 2009, 6:48PM
- Forum: eCabinet Systems Software
- Topic: Wish List for Version 6
- Replies: 6
- Views: 5247
Wish List for Version 6
I would like to see a line boring option added to Version 6 . Set up where you can reverence the first hole from the bottom (or top) and where both front and back holes are referenced from the front of the cabinet. Referencing both holes from the front would be more accurate for drawer glides. This ...
- Sat, May 30 2009, 1:28AM
- Forum: eCabinet Systems Software
- Topic: Metabox drawers HELP
- Replies: 10
- Views: 8459
Re: Metabox drawers HELP
Nat how I loaded Iain's HSF file is: 1. I have a file called Downloads in my Cabinet directory. You can create a download file by just saving any cabinet and naming the directory downloads. 2. I saved the HSF file to that downloads file. You can then open the file like any other cabinet. 3. How to g...
- Thu, May 28 2009, 10:17PM
- Forum: eCabinet Systems Software
- Topic: Adding Possitive edge banding
- Replies: 4
- Views: 5318
Re: Adding Possitive edge banding
Jay put 0 on the thickness as your banding thickness. Most .5 mil edge banding is .020 thick with the glue line. That means that you have two options. Option 1 - ask your edge bander to only pre mill .020 . Option 2- if your edge bander pre mills .030 your part will only be .010 smaller that is and ...
- Wed, May 27 2009, 9:21PM
- Forum: eCabinet Systems Software
- Topic: Metabox drawers HELP
- Replies: 10
- Views: 8459
Re: Metabox drawers HELP
The downloadable library that Jason is talking about is the System 32mm Frameless. One tip that might help is on Blum metabox drawers the mounting hole reference points are different on tall drawers than short drawers plus the spread between holes changes on tall drawer fronts. So if you are manuall...
- Tue, Apr 28 2009, 10:31AM
- Forum: eCabinet Systems Software
- Topic: Part Editor Demystified
- Replies: 6
- Views: 4640
Re: Part Editor Demystified
Thanks Dan,
Great document, could not have came at a more incorporate time.
Great document, could not have came at a more incorporate time.
- Tue, Apr 28 2009, 6:52AM
- Forum: eCabinet Systems Software
- Topic: Entertainment Center Project Cleanup
- Replies: 4
- Views: 4895
Re: Entertainment Center Project Cleanup
Great video Dan very informative. Thanks
- Sun, Apr 26 2009, 5:59PM
- Forum: eCabinet Systems Software
- Topic: Top not Cutlisting Correctly/ RTA Fitting
- Replies: 3
- Views: 3545
Re: Top not Cutlisting Correctly/ RTA Fitting
Hi Nat, If you remove the edge banding from the top, the top shows back up in the cut list. I did a quick build using a standard base as a seed cabinet using your dimensions, but with out hanger holes and notch and everything works fine (top shows up in cut list.) Try removing and redoing the notch ...
- Sat, Apr 25 2009, 12:42AM
- Forum: eCabinet Systems Software
- Topic: Top not Cutlisting Correctly/ RTA Fitting
- Replies: 3
- Views: 3545
Re: Top not Cutlisting Correctly/ RTA Fitting
Hi Nat,
I downloaded your file and I am having the same problem. I removed the RTA fittings and the problem goes away. I will try rebuilding the cabinet from scratch this weekend. To see if the same thing happens. I hope that Thermwood will chime in on this post.
I downloaded your file and I am having the same problem. I removed the RTA fittings and the problem goes away. I will try rebuilding the cabinet from scratch this weekend. To see if the same thing happens. I hope that Thermwood will chime in on this post.