Search found 485 matches

by JohnLashuay
Tue, Nov 22 2011, 4:13PM
Forum: Lounge
Topic: If you have employees....
Replies: 4
Views: 8896

Re: If you have employees....

Very good! Thanks for sharing!!
by JohnLashuay
Tue, Nov 08 2011, 10:17AM
Forum: eCabinet Systems Software
Topic: 'An error occurred while trying to read Parasolid file info.
Replies: 4
Views: 4659

Re: 'An error occurred while trying to read Parasolid file i

Hi John, This error is followed by something along the lines of 'unable to save file'. It's become a significant annoyance. Nat The only time that this has happened in the batch is after I have changed the material. This error comes up and then I am unable to save the changes. Thankfully I have sti...
by JohnLashuay
Mon, Nov 07 2011, 4:38PM
Forum: eCabinet Systems Software
Topic: 'An error occurred while trying to read Parasolid file info.
Replies: 4
Views: 4659

Re: 'An error occurred while trying to read Parasolid file i

Nat, are you still able to save the file after you get this error?

I reported an issue a while ago that sounds something like this. It might be fixed in the next release.

-John
by JohnLashuay
Thu, Nov 03 2011, 11:46AM
Forum: eCabinet Systems Software
Topic: Adding double doors changes doors width
Replies: 5
Views: 4840

Re: Adding double doors changes doors width

Thanks guys for checking into this! I usually don't use the gap settings, but I now know that I can try them out to get the proper result.

Thanks again!
-John
by JohnLashuay
Tue, Nov 01 2011, 3:38PM
Forum: eCabinet Systems Software
Topic: Adding double doors changes doors width
Replies: 5
Views: 4840

Adding double doors changes doors width

Does this happen to anyone else??? 1.) std base frameless 2.) grow width to 48" 3.) S/P Editor -> add middle partition 4.) D/Dr Editor -> change settings for doors .4375 hinge side reveal 5.) add double doors to left section (door width is 11.75") 6.) add double doors to right section (doo...
by JohnLashuay
Thu, Oct 27 2011, 1:58PM
Forum: Thermwood 3-Axis Machinery
Topic: Top to Stretch - Dado cut on wrong side
Replies: 8
Views: 7431

Re: Top to Stretch - Dado cut on wrong side

Thanks Georgi! Good to hear!!
by JohnLashuay
Thu, Oct 27 2011, 10:26AM
Forum: Thermwood 3-Axis Machinery
Topic: Top to Stretch - Dado cut on wrong side
Replies: 8
Views: 7431

Re: Top to Stretch - Dado cut on wrong side

Thanks Josh! Everything looked normal until we cut it. Interesting that it happened on 2 different cabinets involving a Top to Stretcher blind dado construction.
by JohnLashuay
Thu, Oct 27 2011, 8:04AM
Forum: Thermwood 3-Axis Machinery
Topic: Top to Stretch - Dado cut on wrong side
Replies: 8
Views: 7431

Re: Top to Stretch - Dado cut on wrong side

Here is the second cabinet.
by JohnLashuay
Thu, Oct 27 2011, 8:03AM
Forum: Thermwood 3-Axis Machinery
Topic: Top to Stretch - Dado cut on wrong side
Replies: 8
Views: 7431

Top to Stretch - Dado cut on wrong side

Hi guys,

Here are 2 cabinets that looked good up until they were cut. In both situations the TOP had s stretch blind dado'd to it. When cut, the dado was on the opposite side than what it should have been.

Can someone take a look at these for me?

Thanks, John!
by JohnLashuay
Thu, Oct 13 2011, 9:15AM
Forum: eCabinet Systems Software
Topic: pie shape lower
Replies: 6
Views: 5818

Re: pie shape lower

Kerry, is there any way to use a back in place of the display panel?
by JohnLashuay
Mon, Oct 03 2011, 2:17PM
Forum: eCabinet Systems Software
Topic: cabinet edit dimensions greyed out
Replies: 14
Views: 10585

Re: cabinet edit dimensions greyed out

Scott G Vaal wrote:Kenneth,
Kerry and or John,
are either of you able to reproduce the greyed dims using the steps in my last post??
No, it looks good for me.
by JohnLashuay
Mon, Oct 03 2011, 9:10AM
Forum: eCabinet Systems Software
Topic: cabinet edit dimensions greyed out
Replies: 14
Views: 10585

Re: cabinet edit dimensions greyed out

Kenneth, I have had this happen as well, specifically with wall cabinets. I am looking forward to the new release, in which some of these issues should be resolved. Somewhere in the process of adjusting your cabinet something may have corrupted it. Try to trace your steps as to what you did to it. C...
by JohnLashuay
Tue, Aug 09 2011, 12:43PM
Forum: Thermwood 3-Axis Machinery
Topic: Slatwall
Replies: 8
Views: 9258

Re: Slatwall

Thanks guys for the help!
by JohnLashuay
Fri, Aug 05 2011, 8:24AM
Forum: eCabinet Systems Software
Topic: Constraints
Replies: 2
Views: 3210

Re: Constraints

I have some standard closet components set up in a library. They have 32mm system holes the length of the panels 72". Is there a quick way to apply constraints to the whole pattern or will I have to add constraints to each hole? Here is a 72" panel that we use in which all the holes are c...

Go to advanced search