Thermwood / eCabinet Systems

Ok but it's not the only file.....what is the procedure for EXPORT again ?

Thank you, I'll hope they'll post it soon cause I have jobs to complete !

Is there any known problems in 5.56 about drawer boxes tenons ? We just machined a job and everything is ok but the drawer boxes, tenons are not the thickness we asked, we use 50% with 0.025 tolerance but they are something like 0.26 thick. I attached the .twd wich I renamed .doc. In eCabs all the s...

After you measure the tool manually, you need to set your switchspoil value to 0.000 and then measure the tool with the sensor. This will give you a daylight value that is the distance from home to just the sensor. You can then take the difference of these two values and use this as your switchspoil...

When I'm runnign the X-Surf program I can't see any ABSOLUTE value anywhere....I can see the daylight wich is 7.904 compared to 7.906, that's good... Is the thickness of the spoilboard wich was set some time ago, could be a factor or it does not matter if my switch spoil is set ?

No I'm not, just did it again and all was ok. If I go manually on the spoilbaord I get 7.906 and if I go with the tool manager I get 8.184, so switch spoil has to be set at 0.278, which means that the sensor is over the table by this value. But when I add my wasteboard (app. 0.240") over the sp...

Ok, than, if I want to start over, but don't change the spoilboard, where should I start, measure the thickness of the spoilboard, enter this thickness, after set the switchspoil following the steps, verify everything than add the wasteboard ? Last week I took off the wasteboard and calculate the se...

Ok, then what might be the reason that can explain why I have to adjust the switch spoil so often ?? I say this because when I fly cut the wasteboard, let's say I ask to take off 0.005, I have to adjust the wasterboard as I would have took off 0.03 ???? So I think I have to adjust the set switch spo...

I'm having problems with somthing since a while, I discussed it here last week but I want to make sure I am doing everything all right. In the M999 there are 2 switchspoil, one that is named "set switchspoil" and one named "set switchspoil2". I think the one I have to adjust is t...

Is the I get : Could'nt find c:/RollingNest/Result.mdb or c:/RollingNest/Result.mdb related to space left on c: drive ???

When I try to nest I get : Could'nt find c:/RollingNest/Result.mdb or c:/RollingNest/Result.mdf and after sometimes I get : No record........It's driving me crazy.....and when it's not those it's : Not enough space........I ordered the c: drive retrofit but it will take 2-3 weeks, I need to machine ...

I think I solved the problem, I re-adjust the set switchspoil , it was not good anymore, but it's always that same problem, is it causes by the switch where I measure my tool ?? It's either this or the 3/4" thick spoilboard that gets thinner as time goes by......(don't think so)

Sorry I meant the wasteboard, we mostly never flycut the spoilboard (once in a year maybe)....but we always had that problem. Once we adjust the spoilboard, the first time we flycut the wasteboard it's ok, couple times later if I flycut 0.015, I have to adjust like if I had took off 0.025...a couple...

Can it be caused by this : When I surface the spoilboard, if I take off 0.02, I have to adjust to something like 0.04 so the outline goes throught ?? It get worse and worse but I do not touch any settings ??

I have sent all the info needed by email yesterday morning but still no feed back, is it something with my file or something with 5.56 ? Is it close to being fixed or should I go back to a previous version ?

Thank you.