Search found 76 matches
- Sat, May 26 2007, 5:25PM
- Forum: eCabinet Systems Software
- Topic: part editor functions
- Replies: 13
- Views: 8150
Anyone still here? I have tried to walk through this in eCabinetSystemsMadeEasy. I go into contour mode, manually enter the three coordinates which gives me the arc I want, switch to line mode and even MANUALLY enter every point to make sure that I am truly connected together... Then there's NOPLACE...
- Sat, May 26 2007, 4:10PM
- Forum: eCabinet Systems Software
- Topic: OK so NOW which editor do I need to be in!
- Replies: 5
- Views: 4631
- Sat, May 26 2007, 4:03PM
- Forum: eCabinet Systems Software
- Topic: OK so NOW which editor do I need to be in!
- Replies: 5
- Views: 4631
OK so NOW which editor do I need to be in!
i'd now like to create stop fluted appliques to the fronts of my bow columns. I cant add moulding vertically... -I cant easily \"equalize\" 0.25\" deep plows that make up a stop flute. -I don't want to use a porter cable router for this ANYMORE. I guess reed columns would be the next ...
- Sat, May 26 2007, 3:18PM
- Forum: eCabinet Systems Software
- Topic: ceiling attributes
- Replies: 6
- Views: 5469
- Sat, May 26 2007, 3:12PM
- Forum: eCabinet Systems Software
- Topic: part editor functions
- Replies: 13
- Views: 8150
- Sat, May 26 2007, 1:52PM
- Forum: eCabinet Systems Software
- Topic: part editor functions
- Replies: 13
- Views: 8150
I was trying to use geometric shapes. My actual parts I'm trying to modify is this: a 10.58x10.58 shelf. It is one of the 3 fixed shelfs in an angled front corner cabinet. Since it is an angled front corner cab, the shelf would best be described as a 10.5x10.5 square that you cropped off at a 45 deg...
- Sat, May 26 2007, 1:27PM
- Forum: eCabinet Systems Software
- Topic: part editor functions
- Replies: 13
- Views: 8150
part editor functions
I am using the parts editor to try to radius the corners OFF of a square. The parts are fixed shelves in an angle front cabinet. for all practical purposes lets view one of the shelves as a 14x14 square. suppose I want to change one of the 90 deg. corners to a 3\" radius ( where normally a jigs...
- Sat, May 26 2007, 12:28AM
- Forum: eCabinet Systems Software
- Topic: corner cabs and parameters
- Replies: 9
- Views: 7027
- Fri, May 25 2007, 4:44PM
- Forum: eCabinet Systems Software
- Topic: corner cabs and parameters
- Replies: 9
- Views: 7027
- Fri, May 25 2007, 10:44AM
- Forum: eCabinet Systems Software
- Topic: corner cabs and parameters
- Replies: 9
- Views: 7027
- Fri, May 25 2007, 10:41AM
- Forum: eCabinet Systems Software
- Topic: corner cabs and parameters
- Replies: 9
- Views: 7027
maybee I'm being too ambiguous... Let's say for example I want a tall cabinet that is angled at 45 degrees on it's right side. ------------------------- - - - - - - - - - - -------------------------------------- sorry for the crudeness, but this should give a quick and dirty illustration of the top/...
- Fri, May 25 2007, 10:33AM
- Forum: eCabinet Systems Software
- Topic: drawer box + stretchers = ? for placement
- Replies: 3
- Views: 3207
I just returned to this thread, and am happy to see I'm on the same wavelength! That was the first thing I tried, but I attempted to delete the fixed shelves, and thought I was going to replace them with stretchers. -I didn't think to adjust backset instead! Thanks! Oh, one more thing... Where do yo...
- Fri, May 25 2007, 10:06AM
- Forum: eCabinet Systems Software
- Topic: drawer box + stretchers = ? for placement
- Replies: 3
- Views: 3207
drawer box + stretchers = ? for placement
I'm trying to load drawer boxes into a drawer base, I have placed stretchers to an \"almost\" equalized spacing increment. I have entered insets and still can't get the drawer boxes to fit into the correct location? they either install too high, too low, -sometimes right over the top of a ...
- Thu, May 24 2007, 10:56PM
- Forum: eCabinet Systems Software
- Topic: corner cabs and parameters
- Replies: 9
- Views: 7027
corner cabs and parameters
I need to design several different seed cabs that are NOT square boxes. I have been trying to do this based on corner cabinets from the standard directory. The \"corner\" tab in the construction area gives alot of options and flexibility, but I can't seem to figure out how to get the basic...
- Thu, May 24 2007, 12:21PM
- Forum: eCabinet Systems Software
- Topic: ceiling attributes
- Replies: 6
- Views: 5469