Search found 536 matches

by Leo Graywacz
Wed, Apr 22 2015, 7:44AM
Forum: eCabinet Systems Software
Topic: Misaligned Crown molding
Replies: 4
Views: 1044

Misaligned Crown molding

I have a cabinet that when you use the crown editor area won't put the corners of the crown together. The problem happens because I have face frame offsets for the side pc of plywood. This puts the plywood side in from the edge of the cabinet by 3/4". Then there is a panel that is applied on th...
by Leo Graywacz
Thu, Apr 02 2015, 5:36PM
Forum: eCabinet Systems Software
Topic: Back of Lazy Susan lower
Replies: 8
Views: 1418

Re: Back of Lazy Susan lower

Wow, lots of weird interactions going on. When you add the top the bottom changes size by getting smaller by 1/4". After you put the top on the 2 side backs develop a leg that is in the dado slot for the back. I've deleted it several times and it comes back, not sure when. I've cut the whole ba...
by Leo Graywacz
Thu, Apr 02 2015, 4:57PM
Forum: eCabinet Systems Software
Topic: Back of Lazy Susan lower
Replies: 8
Views: 1418

Re: Back of Lazy Susan lower

I am having nothing but trouble with the different back thicknesses. The program is based off the center back being the material of the backs. So it treats the other two backs as if they were 3/4" thick. It keeps leaving a 1/4" space between the back and the deck. It also miters the outsid...
by Leo Graywacz
Wed, Apr 01 2015, 11:04PM
Forum: eCabinet Systems Software
Topic: Would be a nice feature in next version
Replies: 1
Views: 692

Re: Would be a nice feature in next version

There seem to be a few things that aren't remembered when you go back. Along with that same thought is when you are in the nesting area and you highlight a pc of plywood to look at the parts within and then you go back you are at the top of the page again. When you put crown on a cabinet and then yo...
by Leo Graywacz
Wed, Apr 01 2015, 10:24PM
Forum: eCabinet Systems Software
Topic: Back of Lazy Susan lower
Replies: 8
Views: 1418

Re: Back of Lazy Susan lower

Here is my 36 x 36 Face Frame Lazy Susan
by Leo Graywacz
Wed, Apr 01 2015, 11:12AM
Forum: eCabinet Systems Software
Topic: Back of Lazy Susan lower
Replies: 8
Views: 1418

Re: Back of Lazy Susan lower

Open a job up that has a Lazy Sue Cabinet or bring one into the room editor. In the room editor highlight the lazy Sue cabinet. Right click your mouse and choose Change Materials. A dialog panel comes up. Uncheck the box on the parts tree so it shows an "X". Open the parts tree up by press...
by Leo Graywacz
Tue, Mar 31 2015, 5:24PM
Forum: eCabinet Systems Software
Topic: Back of Lazy Susan lower
Replies: 8
Views: 1418

Re: Back of Lazy Susan lower

OK, found it. You have to do it from the room editor area. :mrgreen:
by Leo Graywacz
Tue, Mar 31 2015, 3:47PM
Forum: eCabinet Systems Software
Topic: Back of Lazy Susan lower
Replies: 8
Views: 1418

Back of Lazy Susan lower

At one time I remember being able to change the material individually for those backs. Normally in my construction I use 1/2" backs for the side backs and the angle back I would use 3/4" material and that would go to the floor as the third leg. There use to be a way to change it out, I rem...
by Leo Graywacz
Tue, Mar 31 2015, 3:44PM
Forum: eCabinet Systems Software
Topic: It would be nice if....
Replies: 0
Views: 897

It would be nice if....

The depth of the drawer would show up in the editor. Just had fun putting drawers in a couple of times because I didn't check. :wall: Always wondered why it didn't show that dimension anyway.
by Leo Graywacz
Fri, Jan 16 2015, 3:55PM
Forum: eCabinet Systems Software
Topic: Dado Depth
Replies: 2
Views: 961

Dado Depth

The standard for the dado depth seems to be 3/8". Is there a way to change it so it's always 1/4" instead? I rarely use seed cabinets because I am custom and my cabinets are always changing. Or do I have to stop using the built in cabinets and make my own "standard" seeds. I'd li...
by Leo Graywacz
Tue, Jan 06 2015, 9:21PM
Forum: eCabinet Systems Software
Topic: DXF's and profile tools
Replies: 2
Views: 888

Re: DXF's and profile tools

Got it figured out. 1st problem was I didn't start my DFX image at 0,0 I opened the part editor by selecting a part. Then I went into contour mode. Then I opened up the DFX file. I chose trim with the two entity option. And then I went around the DFX object and chose intersecting parts. This connect...
by Leo Graywacz
Tue, Jan 06 2015, 8:10PM
Forum: eCabinet Systems Software
Topic: DXF's and profile tools
Replies: 2
Views: 888

DXF's and profile tools

OK, I'm here again. I made a crown shape in AutoCAD and saved it as a DFX file. I opened the DFX file in the Shape Manager. I chose the make tool icon and then went to chose my contour and it seems to be 16 individual elements instead of a closed contour.

How do I close this so it can be selected?
by Leo Graywacz
Fri, Jan 02 2015, 1:01PM
Forum: eCabinet Systems Software
Topic: Conestoga doors ignore partition and doors overlap
Replies: 6
Views: 2198

Re: Conestoga doors ignore partition and doors overlap

Yep, it's happening on a few of my cabinets. I was wrong about the matching color fixing it. Seems to have reverted back to the big space. Seems sorta random. Some doors/drawers do it, some don't I have a drawer and double door in the same cabinet (with 2 other pairs of doors). The drawer is fine wh...
by Leo Graywacz
Fri, Jan 02 2015, 12:09PM
Forum: eCabinet Systems Software
Topic: Mixed FF and Euro
Replies: 0
Views: 927

Mixed FF and Euro

A lot of my cabs are mixed. I have FFs surrounding the outers of the cabinet and the insides are Euro, meaning tight margins (5/64") between doors with only the partition or fixed shelf behind the door/drawer. I remember being able to put a pair of doors into the cabinet by using a large offset...

Go to advanced search