Search found 413 matches
- Sat, Dec 08 2007, 8:30AM
- Forum: Customer Images
- Topic: OT: NOT an eCabs job...
- Replies: 17
- Views: 20974
Re:
. ...I'm just unsure what would happen when the water gets into the skimmer during the winter. Of course, we haven't had a "hard freeze" in 50 years so it may not be a concern. Ahhh...Sorry I did not address this earlier. The skimmer lines are sealed shut after winterizing, using large ru...
- Sat, Dec 08 2007, 8:22AM
- Forum: Customer Images
- Topic: OT: NOT an eCabs job...
- Replies: 17
- Views: 20974
Re:
. ...One question though...we were told to drain the water level to just under the skimmer for the winter. If rain runs through the mesh, do you have any freezing problems? I believe you probably have a little bit colder winters than we do here :D Do you just blow the lines out and not drain the po...
- Fri, Dec 07 2007, 8:46PM
- Forum: eCabinet Systems Software
- Topic: Miter front to corner cabinet
- Replies: 18
- Views: 13796
.
Thanks, Kerry. I must remember this when I see something strange going on.
Al
http://blog.sandal-woods.com
.
Thanks, Kerry. I must remember this when I see something strange going on.
Al
http://blog.sandal-woods.com
.
- Fri, Dec 07 2007, 8:07PM
- Forum: eCabinet Systems Software
- Topic: Miter front to corner cabinet
- Replies: 18
- Views: 13796
Re:
. When you extrude any part of the cabinet beyond the cabinet dimensions, they become really funky and don't want to act right. Kerry's inset is the best way for sure. Just to follow through: In the attached image: 1. Should I offset the sides, or the top and deck? 2. What I need: I will be using k...
- Fri, Dec 07 2007, 1:15PM
- Forum: eCabinet Systems Software
- Topic: Miter front to corner cabinet
- Replies: 18
- Views: 13796
- Fri, Dec 07 2007, 9:54AM
- Forum: eCabinet Systems Software
- Topic: Miter front to corner cabinet
- Replies: 18
- Views: 13796
Re:
Doug, The proper way to build this cabinet would be to take off all the insets on your left and right sides then add a 1.25" bottom inset to the deck. Remove the scribes to your face frame. Go to corner settings and check the Left and right sides mitered box. This causes eCabinets to add enoug...
- Mon, Dec 03 2007, 5:55PM
- Forum: Customer Images
- Topic: Girls Dresser. Sorry, I messed up. Here is the ecabinets pic
- Replies: 8
- Views: 10848
John,
Where in Missouri are you located? Please let me know. I am near St Joseph, in NW MO. Welcome to the forum!
Al
http://blog.sandal-woods.com
Where in Missouri are you located? Please let me know. I am near St Joseph, in NW MO. Welcome to the forum!
Al
http://blog.sandal-woods.com
- Wed, Nov 21 2007, 3:01PM
- Forum: eCabinet Systems Software
- Topic: Question about the Quadro tweak utility
- Replies: 9
- Views: 6962
- Wed, Nov 21 2007, 10:33AM
- Forum: eCabinet Systems Software
- Topic: Question about the Quadro tweak utility
- Replies: 9
- Views: 6962
- Wed, Nov 21 2007, 8:59AM
- Forum: eCabinet Systems Software
- Topic: Question about the Quadro tweak utility
- Replies: 9
- Views: 6962
- Tue, Nov 20 2007, 11:46PM
- Forum: eCabinet Systems Software
- Topic: Question about the Quadro tweak utility
- Replies: 9
- Views: 6962
Re: Question about the Quadro tweak utility
I lurk quite a bit here & will someday be a contributor. In the meantime, can anyone help with this? Last week I bought an M90 from the Dell business outlet. It has a Quadro FX 3500 video card w/512MB. I've installed the latest NVidia driver (& checked to make sure it is properly installed)...
- Wed, Nov 07 2007, 8:41PM
- Forum: eCabinet Systems Software
- Topic: Noobee with a question?
- Replies: 3
- Views: 3613
Re: Noobee with a question?
I hope this is not a totally stupid question but I am just beginning to try to learn this program. Totally intimidating... Dave, Welcome to the forum! Please, understand that the ONLY stupid question is one you don't ask. No matter how simple it appears, if YOU don't know HOW to do something in the...
- Wed, Nov 07 2007, 2:16PM
- Forum: eCabinet Systems Software
- Topic: M90
- Replies: 7
- Views: 5477
Re:
This kinda caught me off guard a little. Since we are a VAR for Dell, I access the Dell site through their Extranet. We can still buy the M90. After Jason pointed out your posting, I went and did a double-check and sure enough, the retail store no longer lists the M90 but the Extranet still does. A...
- Tue, Nov 06 2007, 10:49AM
- Forum: eCabinet Systems Software
- Topic: Problems with Detail Room
- Replies: 9
- Views: 7826
- Tue, Nov 06 2007, 10:48AM
- Forum: eCabinet Systems Software
- Topic: Problems with Detail Room
- Replies: 9
- Views: 7826
Update: I looked at eCabinets.ini, and found that PlaceItemGridSpacing=0.0312 !!! I changed this to 12 inches, and NOW all is well. My thanks to all who have looked into this. I have no idea what might have changed this setting, but now all seems well. My sincere thanks to Scott, to Justin, and to J...