Thermwood / eCabinet Systems

PREFECT!

Leo's the MAN!!!

Hello. I have attached a cabinet for you to look at with a door location problem. It's kinda weird, but what I have here is a cabinet that is sharing the face frame from the cabinet to the left (not shown). So the cabinet on the left has bigger face frames to overlap into the next cabinet so there a...

Hello. How do you create a curved wall? Actually I have a pony wall that heads south down the page and then turns 90 degrees west but not at 90 degrees (that would be way too easy). It follows a smooth curve like a fillet/round. I have the dimensions of the total wall lengths, but I now need to roun...

Dennis, Actually, there was a lot of information in your post. I didn't think about doing it that way because I only needed to put out a total of 4 cabinets from the wall. The problem I had with setting the increment to 1" and using the SHIFT+arrow key trick was the wall was on an angle. I've n...

Hi. I can't seem to figure out how to move a cabinet 1" away from a wall. I want the front of a cabinet to be 25" off a wall, but I only want the cabinet to be 24" in depth (build reasons). I tricked it by making the cabinet 25" in depth then resizing it to 24" and adjusting...

Hi. Is there a way to rename cabinets after they are created? Right now when my builder looks at the plans from left to right I go from cabinet 4 to 6 to 1 to 2 to 5 to 7 and to 3. I'm all over the place. It would be nice to be able to rename them so the builder has something more sequential to look...

Hello. I created all the cabinets in an office and I wanted to show the correct wood species on the material and cut list. I selected Walnut for all the pieces. For some reason the face frames are not updating correctly. The upper and lower face frame have both changed to walnut and the cut list ref...

Hello. I have a room with a few walls that have angles. I went to the job to verify the Builders measurements for wall lengths and guess what??? Never mind. So now I need to edit my wall lengths, but when I increase the length of a wall it breaks the joint of the adjacent wall. I attached the file f...

Hi. I have had these settings set before and it did not seem to work. I had it set to the Back. Are there any other ways to get cabinets to butt up to each other or are those two suggestions the best? Btw, the first post got me going, thx. I think it should work like you suggested, but I must have b...

Hello. Can someone help me get my cabinets to butt up against each other? I can manually shift them side to side and get them really close, but now I'm pulling dimensions off wall and looking at the separation between cabinets and I'm off by tiny bits here and there. If I could move them by 1/64&quo...

I'm no expert by any means, but it seems to me that if you created any unique items on your desktop (jpegs, custom wallpaper...) then you would have to copy those unique files to your laptop AND also re-associate the project to the file locations on your laptop as well. When you open the project on ...

Hello. I am using the V5 Training Guide by Dennis L. Englert (April 2007 ver 5.1) book to guide me through the process of creating a contour in a toe kick. If fact, what I want is EXACTLY what is show on page 241!! You'd think this would be a snap. No so much... I don't get it. As I read it I get co...

Kerry,

You got both of my problems resolved!! Thank you.

However, in the process of moving forward on the project, I think another set of problems have arrived!!

More to follow in a new post.

Have a great weekend.

Adam

Hi Kerry, Thanks for the hand. I did the reverse build on the wall, but it still did not fix either of the problems I am having (cabinet sides getting shrunk when face frames are added and the cabinet float/sink problem). I reattached a new saved version of the corrected walls and replaced cabinets ...

Hello.

I just attached the job I have started.

If you also read the other topic I posted about the cabinet placement I am having this file will show that issue as well.

Any help is great, I'm new!!

Adam