Search found 431 matches
- Fri, Jul 03 2009, 3:33PM
- Forum: eCabinet Systems Software
- Topic: Change Joint on Detached Toe
- Replies: 9
- Views: 5306
Change Joint on Detached Toe
How would I get the front piece to extend the width of the unit? (In other words, have the side pieces die in to the back of the front piece?) The front is set up as a stretcher.
- Fri, Jul 03 2009, 1:22PM
- Forum: eCabinet Systems Software
- Topic: Corner Cabinet Width
- Replies: 6
- Views: 3855
Re: Corner Cabinet Width
Thanks for the help, guys. I was misinterpreting the 'front width' to be the width of the cabinet opening, not the overall front width of the cabinet. I added the setbacks for the top and deck, and have the cabinet I'm after. Thanks again, I'm glad to be able to add this to my library. I was putting...
- Fri, Jul 03 2009, 11:12AM
- Forum: eCabinet Systems Software
- Topic: Corner Cabinet Width
- Replies: 6
- Views: 3855
Re: Corner Cabinet Width
Dan,
I'm not completely clear on the terminology. The cabinet would come out of the corner 610mm in each direction.
I'm not completely clear on the terminology. The cabinet would come out of the corner 610mm in each direction.
- Fri, Jul 03 2009, 10:00AM
- Forum: eCabinet Systems Software
- Topic: Corner Cabinet Width
- Replies: 6
- Views: 3855
Corner Cabinet Width
I'm trying to set this cabinet up to be 610mm wide (across both backs), have the each of the actual cabinet sides be 304mm, and have a 406mm front opening. No matter what I try I can't seem to get these dimensions to work out on the cabinet. (I've put a 19mm inset on the sides to get them to cutlist...
- Thu, Jul 02 2009, 7:15PM
- Forum: eCabinet Systems Software
- Topic: Angled Upper: Remove Back Clip?
- Replies: 5
- Views: 3515
Re: Angled Upper: Remove Back Clip?
Thanks again Kerry. I played around with that one quite a bit, and could not figure out what was going on.
- Thu, Jul 02 2009, 6:31PM
- Forum: eCabinet Systems Software
- Topic: Angled Upper: Remove Back Clip?
- Replies: 5
- Views: 3515
Re: Angled Upper: Remove Back Clip?
Very easy, thanks very much for the help.
I'm setting my right and left depth at 304mm, but the actual size of the sides ends up at 324. I had thought that the right and left depth of the cabinet woyuld match the width of the right and left sides?
Nat
I'm setting my right and left depth at 304mm, but the actual size of the sides ends up at 324. I had thought that the right and left depth of the cabinet woyuld match the width of the right and left sides?
Nat
- Thu, Jul 02 2009, 5:48PM
- Forum: eCabinet Systems Software
- Topic: 'Material not found'
- Replies: 3
- Views: 2668
Re: 'Material not found'
Is there a way to change the door material, aside from redoing the doors?
- Thu, Jul 02 2009, 4:59PM
- Forum: eCabinet Systems Software
- Topic: Angled Upper: Remove Back Clip?
- Replies: 5
- Views: 3515
Angled Upper: Remove Back Clip?
Wasn't able to figure out how (if possible?) to remove the 45 degree clip on the back of this corner cabinet. Is there a way to do it
- Thu, Jul 02 2009, 2:53PM
- Forum: eCabinet Systems Software
- Topic: 'Corner Settings'?
- Replies: 4
- Views: 2731
Re: 'Corner Settings'?
Found the standard cabinets on my other computer. I think I must have deleted that folder on my main design computer, but have now pulled it in from the other.
Thanks.
Thanks.
- Thu, Jul 02 2009, 1:17PM
- Forum: eCabinet Systems Software
- Topic: 'Corner Settings'?
- Replies: 4
- Views: 2731
Re: 'Corner Settings'?
Kerry,
Where do I find the 'Standard Corner Cabinets'? Are they in one of the downloadable libraries?
Where do I find the 'Standard Corner Cabinets'? Are they in one of the downloadable libraries?
- Thu, Jul 02 2009, 11:52AM
- Forum: eCabinet Systems Software
- Topic: 'Material not found'
- Replies: 3
- Views: 2668
Re: 'Material not found'
Thanks Dan.
- Wed, Jul 01 2009, 6:17PM
- Forum: eCabinet Systems Software
- Topic: 'Corner Settings'?
- Replies: 4
- Views: 2731
'Corner Settings'?
I'm trying to design a 45 degree corner cabinet, and have seen mention of a 'corner settings' tab in the Cabinet Editor. I can't seem to find it. Has it been removed, or do I have it turned off, or...?
- Wed, Jul 01 2009, 3:39PM
- Forum: eCabinet Systems Software
- Topic: Grain Direction on Drawer Fornt Won't Stick
- Replies: 2
- Views: 2381
Re: Grain Direction on Drawer Fornt Won't Stick
Thanks. Foolishly, I was using an image without a grain pattern for the door and drawer front material. Once I changed to an image with grain, I was able see fairly quickly what I was doing wrong.
- Wed, Jul 01 2009, 3:00PM
- Forum: eCabinet Systems Software
- Topic: 'Material not found'
- Replies: 3
- Views: 2668
'Material not found'
I keep having odd materials surface when I try to load cabinets into the the cabinet editor. I get the 'material not found' error. It's the same material each time, but on different cabinets. I don't know where it's coming from, its not a material that I have used. How do I eliminate this? Thanks.
- Wed, Jul 01 2009, 10:55AM
- Forum: eCabinet Systems Software
- Topic: 'Ramped' Pockets?
- Replies: 7
- Views: 5194
Re: 'Ramped' Pockets?
Dan,
Thanks very much for taking the time to post. Sorry not to have mentioned that I was using the SB Link, I didn't realize that it would factor in.
Nat
Thanks very much for taking the time to post. Sorry not to have mentioned that I was using the SB Link, I didn't realize that it would factor in.
Nat