Open the attached cabinet derived from V6 std base framed. The top dado settings are set to 1 1/2" on the R & L fronts, but they show as 1". If set at 2" all seems fine. When the top is taken into the PE for a closer look it returns a "funky" little geometric quirk between 1" and 1 1/2" on the tenon dado.
The nest shows a similar error.
V6b2 Construction Settings
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal
-
- Guru Member
- Posts: 256
- Joined: Sat, Apr 04 2009, 6:27PM
- Company Name: ShopBot Tools Inc
- Country: UNITED STATES
- Location: Durham NC
V6b2 Construction Settings
Gary Campbell
ShopBot Tools Production Support
ShopBot (eCabinets) Link Training & Support
ShopBot Tools Production Support
ShopBot (eCabinets) Link Training & Support
-
- Guru Member
- Posts: 256
- Joined: Sat, Apr 04 2009, 6:27PM
- Company Name: ShopBot Tools Inc
- Country: UNITED STATES
- Location: Durham NC
Re: V6b2 Construction Settings
Another note.....
The Nest shows this as a pocket with a depth of .5"
The Nest shows this as a pocket with a depth of .5"
Gary Campbell
ShopBot Tools Production Support
ShopBot (eCabinets) Link Training & Support
ShopBot Tools Production Support
ShopBot (eCabinets) Link Training & Support
-
- Thermwood Team
- Posts: 1740
- Joined: Tue, May 17 2005, 12:44PM
- Company Name: Thermwood Corporation
- Location: Thermwood Corp: Dale, Indiana
- Contact:
Re: V6b2 Construction Settings
Gary,
I removed the PE cut from the top and added it back on and cannot reproduce this. Could you please give me some steps to reproduce this issue. At this point this does not look like a V6b2 issue, just maybe a scenario that you may have found. Anyway, if you can give me some steps, that would be great. Much appreciated...
I removed the PE cut from the top and added it back on and cannot reproduce this. Could you please give me some steps to reproduce this issue. At this point this does not look like a V6b2 issue, just maybe a scenario that you may have found. Anyway, if you can give me some steps, that would be great. Much appreciated...
Regards,
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000
-
- Guru Member
- Posts: 256
- Joined: Sat, Apr 04 2009, 6:27PM
- Company Name: ShopBot Tools Inc
- Country: UNITED STATES
- Location: Durham NC
Re: V6b2 Construction Settings
Scott...
In V5.2, virtually all of my base cabs has this "web Top" some have had the blind dado joinery for the partition. None have had the PE cuts to the partition shown in another post. None have shown this error. It may be a product of changing the Dado front stops last or the combination of PE cuts that caused it.
I also found that removing PE cuts from top & partition resulted in I cannot reproduce on my machine.
I can forget about this until its repeatable.
In V5.2, virtually all of my base cabs has this "web Top" some have had the blind dado joinery for the partition. None have had the PE cuts to the partition shown in another post. None have shown this error. It may be a product of changing the Dado front stops last or the combination of PE cuts that caused it.
I also found that removing PE cuts from top & partition resulted in I cannot reproduce on my machine.
I can forget about this until its repeatable.
Gary Campbell
ShopBot Tools Production Support
ShopBot (eCabinets) Link Training & Support
ShopBot Tools Production Support
ShopBot (eCabinets) Link Training & Support
-
- Thermwood Team
- Posts: 1740
- Joined: Tue, May 17 2005, 12:44PM
- Company Name: Thermwood Corporation
- Location: Thermwood Corp: Dale, Indiana
- Contact:
Re: V6b2 Construction Settings
Thanks for the reply Gary. I tried changing the insets for the dados after the PE cuts and it still is working OK. Just let me know if you run across it again. Thanks for the feedback.
Regards,
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000