Problem with holes showing up

Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal

Nick Sollecito
Junior Member
Posts: 51
Joined: Sun, Mar 05 2006, 11:03AM
Location: Swansea, MA
Contact:

Problem with holes showing up

Post by Nick Sollecito »

I cannot seem to get the holes to show up in the ecabinet nesting window. I created my own hole pattern for a slide that I also created in the hardware library. In the cabinet editor, I added the slide and hole pattern to the drawer as well as the draw box. When I nest the cabinet I cannot see the holes on the left and right side of the cabinet. Could it be that they do not show up here but will show up in the Controller Nest?
Thanks!
Nick Sollecito
Home Genius
http://www.MyHomeGenius.com
ynd@comcast.net
David Egnoski
Senior Member
Posts: 209
Joined: Tue, May 17 2005, 1:05PM
Company Name: Richmond Cabinet
Country: UNITED STATES
Location: Delavan, WI

Re: Problem with holes showing up

Post by David Egnoski »

Nick,

I've noticed this myself. I think it's just a display issue. They do seem to make it to the finished parts.
Dave Egnoski
Richmond Cabinet & Millwork
Nick Sollecito
Junior Member
Posts: 51
Joined: Sun, Mar 05 2006, 11:03AM
Location: Swansea, MA
Contact:

Re: Problem with holes showing up

Post by Nick Sollecito »

That's great news! I'll run a part and check it.
Thanks!
Nick Sollecito
Home Genius
http://www.MyHomeGenius.com
ynd@comcast.net
Rick Palechuk
Wizard Member
Posts: 1896
Joined: Wed, May 18 2005, 7:54PM
Company Name: Milltech Millworks Ltd.
Country: CANADA
Location: Edmonton, Alberta
Contact:

Re: Problem with holes showing up

Post by Rick Palechuk »

Nick, can you post a cabinet with this hole pattern.
Nick Sollecito
Junior Member
Posts: 51
Joined: Sun, Mar 05 2006, 11:03AM
Location: Swansea, MA
Contact:

Re: Problem with holes showing up

Post by Nick Sollecito »

I tried running the right side to see if the holes drill but they did not.
Thanks for taking a look Rick.
Attachments
24 .X 34.75 x 26.5 Draw Base.jpg
24 .X 34.75 x 26.5 Draw Base.jpg (18.1 KiB) Viewed 12246 times
24 .X 34.75 x 26.5 Draw Base.hsf
(2.16 MiB) Downloaded 343 times
Nick Sollecito
Home Genius
http://www.MyHomeGenius.com
ynd@comcast.net
Nat Wheatley
eCabinets Beta Tester
Posts: 491
Joined: Wed, Apr 15 2009, 8:22PM
Company Name: Plymouth Custom Closets
Country: UNITED STATES
Location: Plympton, MA

Re: Problem with holes showing up

Post by Nat Wheatley »

Nick,

One quick thing to rule out if you haven't already: make sure that the holes for the slide pattern have a negative depth assigned to them. View the pattern in the Hardware Hole Editor, in 3D (eye icon), to see. I've had the issue you've described, and it was caused by the holes having a depth of '0'.

I've also had the slide pattern not take, on occasion, but eventually got it appear by deleting the drawer or front (depending on which you've used to place the slide) entirely and then recreating it.

Nat
http://www.plymouthcustomclosets.com

Dell Precision 490/ Intel Xeon 3.20 Ghz/3 GB RAM/ Nvidia Quadro FX 3450/ Windows XP, sp 3
Rick Palechuk
Wizard Member
Posts: 1896
Joined: Wed, May 18 2005, 7:54PM
Company Name: Milltech Millworks Ltd.
Country: CANADA
Location: Edmonton, Alberta
Contact:

Re: Problem with holes showing up

Post by Rick Palechuk »

Nick, can you send me the hole pattern. You will need to zip it to post it.
Nick Sollecito
Junior Member
Posts: 51
Joined: Sun, Mar 05 2006, 11:03AM
Location: Swansea, MA
Contact:

Re: Problem with holes showing up

Post by Nick Sollecito »

Hi Rick,
I attached the file.
Thanks!
Nick
Attachments
muvb 21.zip
(2.37 KiB) Downloaded 331 times
Nick Sollecito
Home Genius
http://www.MyHomeGenius.com
ynd@comcast.net
Rick Palechuk
Wizard Member
Posts: 1896
Joined: Wed, May 18 2005, 7:54PM
Company Name: Milltech Millworks Ltd.
Country: CANADA
Location: Edmonton, Alberta
Contact:

Re: Problem with holes showing up

Post by Rick Palechuk »

Hi Nick, what I have found out is the pattern doesn't seem to want to stick to a face frame cabinet. It shows in the CE, but it wont nest. A frameless cabinet will nest with the pattern. I have tried different hole depths too. This could be a bug. Maybe someone else can give it a go.
Attachments
Hole pattern.jpg
Hole pattern.jpg (41.33 KiB) Viewed 12147 times
Nat Wheatley
eCabinets Beta Tester
Posts: 491
Joined: Wed, Apr 15 2009, 8:22PM
Company Name: Plymouth Custom Closets
Country: UNITED STATES
Location: Plympton, MA

Re: Problem with holes showing up

Post by Nat Wheatley »

Does appear to be a bug. I tired, and also couldn't get the holes to nest on the side panel of a face frame cabinet.

I tried it on a framed overlay cabinet, not inset, and the front hole did end up showing up on the inside edge of the left and right stiles. Pattern is there, just not drilling on the side panels as it should.
http://www.plymouthcustomclosets.com

Dell Precision 490/ Intel Xeon 3.20 Ghz/3 GB RAM/ Nvidia Quadro FX 3450/ Windows XP, sp 3
Nick Sollecito
Junior Member
Posts: 51
Joined: Sun, Mar 05 2006, 11:03AM
Location: Swansea, MA
Contact:

Re: Problem with holes showing up

Post by Nick Sollecito »

Ok, at least it's not something that I am doing. I'm surprised that no one else has come across this. Is Jason the best person to run this by?
Nick Sollecito
Home Genius
http://www.MyHomeGenius.com
ynd@comcast.net
Paul Huff
Junior Member
Posts: 95
Joined: Thu, May 19 2005, 12:32AM
Location: Lubbock, Texas

Re: Problem with holes showing up

Post by Paul Huff »

I too have had problems with this since build 2. I just installed build 3 and still can't get the hole patterns to take on a face frame cabinet. The pattern is there and shows to go into the sides when viewing the hole patterns. But there are no holes in the cabinet. Funny thing is I can load up some cabinets done with build 1 and they are there.
Kerry Fullington
Wizard Member
Posts: 4718
Joined: Mon, May 09 2005, 7:33PM
Company Name: Double E Cabinets
Country: UNITED STATES
Location: Amarillo, TX

Re: Problem with holes showing up

Post by Kerry Fullington »

I get the same results.
Holes show up on frameless cabinet but not face frame.
(even using the v6 standard cabinets)
Forrest Chapman
eCabinets Beta Tester
Posts: 1230
Joined: Mon, May 30 2005, 2:26PM
Location: Anderson SC.
Contact:

Re: Problem with holes showing up

Post by Forrest Chapman »

Oops, now I feel bad. I had this problem on my cabinet a month ago and in the craziness of beta testing forgot to report it.
Attachments
buffet2.hsf
(3.44 MiB) Downloaded 333 times
Rick Deskins
Thermwood Team
Posts: 857
Joined: Tue, May 17 2005, 12:47PM
Company Name: Thermwood
Country: UNITED STATES
Location: Thermwood

Re: Problem with holes showing up

Post by Rick Deskins »

Yes this is a bug. It will be fixed in the next release (dont ask, i dont know at this time when that will be). This was a bug that was introduced in V6 Build2.

Rick
Rick Deskins
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900
Post Reply