Base Angle Cabinet

Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal

Paul Bruce
New Member
Posts: 10
Joined: Wed, Dec 14 2005, 8:09PM
Contact:

Base Angle Cabinet

Postby Paul Bruce » Thu, Apr 15 2010, 11:25AM

How can I add doors to a cabinet like this? All I did was put a front inset on the left end and angled the top and deck in the part editor. When I try to add doors it still applies them as if it were a full depth gable.
Attachments
Base Angle 30.esj
(12.02 KiB) Downloaded 47 times

Paul Bruce
New Member
Posts: 10
Joined: Wed, Dec 14 2005, 8:09PM
Contact:

Re: Base Angle Cabinet

Postby Paul Bruce » Thu, Apr 15 2010, 1:08PM

Sorry, not sure if that file worked, here is a jpg. of the cabinet.
Attachments
base angle.jpg
base angle.jpg (52.61 KiB) Viewed 1119 times

Sean Jakob
Junior Member
Posts: 75
Joined: Tue, Feb 16 2010, 2:39PM
Company Name: Sean Jakob Cabinets

Re: Base Angle Cabinet

Postby Sean Jakob » Sun, Apr 18 2010, 5:45AM

You have started with a standard cabinet. Start with a corner cabinet instead.

Then go into the construction settings and under the Corner settings, you can tell it to have an angled front.

It should all become self explanatory from there.

Paul Bruce
New Member
Posts: 10
Joined: Wed, Dec 14 2005, 8:09PM
Contact:

Re: Base Angle Cabinet

Postby Paul Bruce » Mon, Apr 19 2010, 6:27PM

I'm not looking to create a standard corner cabinet with and angled front. This is an angle cabinet that would go at the end of a run of cabinets. If I try to start with a corner cabinet I would have to somehow place a door where the gable is.
If I start with a standard cabinet I can add doors manually and place them using align part but I can't get the hardware holes to show up.

Sean Jakob
Junior Member
Posts: 75
Joined: Tue, Feb 16 2010, 2:39PM
Company Name: Sean Jakob Cabinets

Re: Base Angle Cabinet

Postby Sean Jakob » Tue, Apr 20 2010, 6:23PM

Is this the sort of cabinet that you mean?

It was created with a corner cabinet, yet it is used to finish a run of cabinets (at the entry to the room, not back in one of the corners)
BCLIP LH.jpg
created from a corner cabinet
BCLIP LH.jpg (5.88 KiB) Viewed 1079 times


Here is another
BCLIP LH.jpg
created from a corner cabinet
BCLIP LH.jpg (5.88 KiB) Viewed 1079 times
Attachments
Angle Front 600_450 LHS Display.jpg
and another
Angle Front 600_450 LHS Display.jpg (9.19 KiB) Viewed 1079 times

Paul Bruce
New Member
Posts: 10
Joined: Wed, Dec 14 2005, 8:09PM
Contact:

Re: Base Angle Cabinet

Postby Paul Bruce » Tue, Apr 20 2010, 6:40PM

Yeah exactly, but I want two doors on it - one on the angle and another on the front. Do those have two doors?
Thanks.

Sean Jakob
Junior Member
Posts: 75
Joined: Tue, Feb 16 2010, 2:39PM
Company Name: Sean Jakob Cabinets

Re: Base Angle Cabinet

Postby Sean Jakob » Tue, Apr 27 2010, 2:30PM

No it only has a door on the angle, but it does have two fixed panels in the two faces adjacent to the door. These were added as display parts.

Hope this helps


Return to “eCabinet Systems Software”

Who is online

Users browsing this forum: No registered users and 11 guests