pie shape lower

Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal

FredHirsch
Senior Member
Posts: 167
Joined: Tue, Oct 03 2006, 6:51PM
Location: Phoenix, AZ
Contact:

pie shape lower

Postby FredHirsch » Tue, Oct 11 2011, 11:50PM

Is there any way to do a pie shaped lower cabinet with less than 90degree angle? We have a number of these to do and I can't seem to figure a way to do them. Front of the box is the 20" leg.
Thanks,
Fred
Attachments
pie.jpg
Fred Hirsch

User avatar
Kerry Fullington
Wizard Member
Posts: 4593
Joined: Mon, May 09 2005, 7:33PM
Company Name: Double E Cabinets
Country: UNITED STATES
Location: Amarillo, TX

Re: pie shape lower

Postby Kerry Fullington » Wed, Oct 12 2011, 6:31AM

Fred,

Is this what you are looking for. I will have to play with it a bit more to get your exact measurements.


fred_03.jpg

FredHirsch
Senior Member
Posts: 167
Joined: Tue, Oct 03 2006, 6:51PM
Location: Phoenix, AZ
Contact:

Re: pie shape lower

Postby FredHirsch » Wed, Oct 12 2011, 10:38AM

Kerry that is it. Measurements above are not necessarily what I need. I'm mostly just trying to figure out how you did that. We get all different measurements and right now in the dark ages esentially making on table saw.
Thx
Fred
Fred Hirsch

User avatar
Kerry Fullington
Wizard Member
Posts: 4593
Joined: Mon, May 09 2005, 7:33PM
Company Name: Double E Cabinets
Country: UNITED STATES
Location: Amarillo, TX

Re: pie shape lower

Postby Kerry Fullington » Wed, Oct 12 2011, 7:33PM

Fred,

I have attached the cabinet I was playing with for you to look at. I am not sure it will work though. I had to use a display panel for the back so it won't automatically re-size.
I will keep playing with it.

Kerry
Attachments
pie cut_02.hsf
(180.02 KiB) Downloaded 121 times

JohnLashuay
Guru Member
Posts: 645
Joined: Mon, Nov 20 2006, 3:39PM
Company Name: Rylex Custom Cabinetry-Close
Country: UNITED STATES
Location: Pine Island, New York
Contact:

Re: pie shape lower

Postby JohnLashuay » Thu, Oct 13 2011, 9:15AM

Kerry, is there any way to use a back in place of the display panel?
Rylex Custom Cabinetry & Closets
http://www.rylexonline.com
Thermwood CS 43

User avatar
Kerry Fullington
Wizard Member
Posts: 4593
Joined: Mon, May 09 2005, 7:33PM
Company Name: Double E Cabinets
Country: UNITED STATES
Location: Amarillo, TX

Re: pie shape lower

Postby Kerry Fullington » Thu, Oct 13 2011, 11:48AM

John,

This was done using a corner cabinet and with the three piece back I can't get it to work. The center back is just a bit short to make the cuts.

I am going to try this using a miter fold.

Kerry

FredHirsch
Senior Member
Posts: 167
Joined: Tue, Oct 03 2006, 6:51PM
Location: Phoenix, AZ
Contact:

Re: pie shape lower

Postby FredHirsch » Tue, Oct 25 2011, 12:11PM

Kerry,
That is it. I still need to get my head around the corner cab numbers and what all changes. Display panel is not a problem.
Thanks,
Fred
Fred Hirsch


Return to “eCabinet Systems Software”

Who is online

Users browsing this forum: No registered users and 13 guests