Partition not following settings

Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal

JohnLashuay
Guru Member
Posts: 645
Joined: Mon, Nov 20 2006, 3:39PM
Company Name: Rylex Custom Cabinetry-Close
Country: UNITED STATES
Location: Pine Island, New York
Contact:

Partition not following settings

Postby JohnLashuay » Thu, Apr 05 2012, 8:11AM

Here is a hutch cabinet that has a center partition in the lower section that looks like it has a neg inset for the top, but it is set at 0. Can someone look at this? I can't make heads or tails of it!!
Thanks!!
-John
Attachments
Hutch_1992_24-24_5-6-6-8-8.hsf
(2.46 MiB) Downloaded 383 times
Rylex Custom Cabinetry & Closets
http://www.rylexonline.com
Thermwood CS 43

Scott G Vaal
Thermwood Team
Posts: 1740
Joined: Tue, May 17 2005, 12:44PM
Company Name: Thermwood Corporation
Location: Thermwood Corp: Dale, Indiana
Contact:

Re: Partition not following settings

Postby Scott G Vaal » Thu, Apr 05 2012, 9:44AM

John,

Not sure here. The version history goes straight from V6Bld6 date saved 6-15-2011 to the release version of V6Bld8 dated 4-2-2012. Do you still have this cabinet as a V6Bld6 cabinet or did you save over your only copy? If not, please get me the V6Bld6 version of the cab. What if any changes did you make to this cabinet in Bld8? Was the cab like that when you loaded it as the V6Bld6? I removed it and then re-added all the parts and cannot seem to get it to reproduce. So not sure if it was an old bug or not. Having the older cab may help me answer that.
Regards,

Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000

JohnLashuay
Guru Member
Posts: 645
Joined: Mon, Nov 20 2006, 3:39PM
Company Name: Rylex Custom Cabinetry-Close
Country: UNITED STATES
Location: Pine Island, New York
Contact:

Re: Partition not following settings

Postby JohnLashuay » Thu, Apr 05 2012, 10:41AM

Hi Scott, I'll look to see if I have something from before.

I already had that partition in place then I noticed there were no KD fittings at the top. As soon as I added the KD's to the top of it the neg inset showed. This all took place shortly after I added neg insets to the left and right ends.

Not sure if this will help. I'll try to track down previous cabinets.

Thanks for checking this out!
-John
Rylex Custom Cabinetry & Closets
http://www.rylexonline.com
Thermwood CS 43

JohnLashuay
Guru Member
Posts: 645
Joined: Mon, Nov 20 2006, 3:39PM
Company Name: Rylex Custom Cabinetry-Close
Country: UNITED STATES
Location: Pine Island, New York
Contact:

Re: Partition not following settings

Postby JohnLashuay » Thu, Apr 05 2012, 11:04AM

Scott, I emailed you some possible cabinets used for this one.

Any questions, let me know!
-John
Rylex Custom Cabinetry & Closets
http://www.rylexonline.com
Thermwood CS 43

Scott G Vaal
Thermwood Team
Posts: 1740
Joined: Tue, May 17 2005, 12:44PM
Company Name: Thermwood Corporation
Location: Thermwood Corp: Dale, Indiana
Contact:

Re: Partition not following settings

Postby Scott G Vaal » Thu, Apr 05 2012, 1:41PM

John,

With the clues you gave me, I finally figured it out. Amazingly it is a long existing issue with resizing the height of a cabinet and then going into the shelf/partition editor, highlighting an existing partition that is attached to a fixed shelf, then going to con-setting and selecting OK. I have this listed and it will be fixed for the next release. Thanks for reporting it. For now, if you have this specific scenario, you would want to change the construction of the partition by right-clicking on it in the main and selecting the construction tiered menu and choose the edge and construction type desired.
Regards,

Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000

JohnLashuay
Guru Member
Posts: 645
Joined: Mon, Nov 20 2006, 3:39PM
Company Name: Rylex Custom Cabinetry-Close
Country: UNITED STATES
Location: Pine Island, New York
Contact:

Re: Partition not following settings

Postby JohnLashuay » Thu, Apr 05 2012, 1:52PM

Thanks Scott! Good to hear.

-John
Rylex Custom Cabinetry & Closets
http://www.rylexonline.com
Thermwood CS 43


Return to “eCabinet Systems Software”

Who is online

Users browsing this forum: Ahrefs [Bot] and 10 guests