drawer box front for pull-outs

Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal

Chris B Campbell
Junior Member
Posts: 84
Joined: Fri, Jul 29 2005, 4:00PM
Location: Helendale, CA.

drawer box front for pull-outs

Postby Chris B Campbell » Sat, Jun 02 2012, 5:41PM

Anyone having a problem in CN with the fronts of pull-out type drawers? (Pantry) We put a 3 point arch in the top of the front panel for a finger pull kind-a-look never had a problem, now CN shows a full circle... of course it goes off the table so were getting an X axis out of bounds?
Anyone else get this
Thanks chris

JohnLashuay
Guru Member
Posts: 645
Joined: Mon, Nov 20 2006, 3:39PM
Company Name: Rylex Custom Cabinetry-Close
Country: UNITED STATES
Location: Pine Island, New York
Contact:

Re: drawer box front for pull-outs

Postby JohnLashuay » Mon, Jun 04 2012, 11:55AM

Hi Chris, I haven't seen anything like this.

Can you post the cabinet?

-John
Rylex Custom Cabinetry & Closets
http://www.rylexonline.com
Thermwood CS 43

Chris B Campbell
Junior Member
Posts: 84
Joined: Fri, Jul 29 2005, 4:00PM
Location: Helendale, CA.

Re: drawer box front for pull-outs

Postby Chris B Campbell » Thu, Jun 07 2012, 6:37PM

Here is what I get after Nesting.
Chris
Attachments
untitled1.jpg

Rick Deskins
Thermwood Team
Posts: 837
Joined: Tue, May 17 2005, 12:47PM
Company Name: Thermwood
Country: UNITED STATES
Location: Thermwood

Re: drawer box front for pull-outs

Postby Rick Deskins » Fri, Jun 08 2012, 8:39AM

Can you post the cabinet file this twd was made with?

Thanks
Rick Deskins
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900

Chris B Campbell
Junior Member
Posts: 84
Joined: Fri, Jul 29 2005, 4:00PM
Location: Helendale, CA.

Re: drawer box front for pull-outs

Postby Chris B Campbell » Sat, Jun 09 2012, 1:09PM

Well I wish I could. I tried to upload the CNC File and the TWD file but these Extensions are not allowed??


Chris

User avatar
Josh Rayburn
eCabinets Beta Tester
Posts: 1261
Joined: Wed, Jul 01 2009, 2:19PM
Company Name: Halls Edge Inc
Country: UNITED STATES
Location: Stamford, CT USA
Contact:

Re: drawer box front for pull-outs

Postby Josh Rayburn » Mon, Jun 11 2012, 6:28AM

Chris,
You can change the extentions to .txt and post them or zip them then post.
jnr
Josh Rayburn
Hall's Edge, Inc.
CNC Machining Service


Dell Precision T3400
Win7 Professional 64 Bit/Core2Duo E8400 3ghz/4 GB Ram/NVIDIA Quadro FX570

Rick Deskins
Thermwood Team
Posts: 837
Joined: Tue, May 17 2005, 12:47PM
Company Name: Thermwood
Country: UNITED STATES
Location: Thermwood

Re: drawer box front for pull-outs

Postby Rick Deskins » Mon, Jun 11 2012, 7:15AM

Chris,
We really need the ecabinets file. The twd/cnc files will show the problem, but it will not helps us tell you why you have the problem or how you might be able to fix it. Please post the ecabinet file.

Thanks,
Rick
Rick Deskins
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900

Chris B Campbell
Junior Member
Posts: 84
Joined: Fri, Jul 29 2005, 4:00PM
Location: Helendale, CA.

Re: drawer box front for pull-outs

Postby Chris B Campbell » Mon, Jun 11 2012, 10:07AM

I thought ecabinets file was a TWD created by ecabinets? So I am not sure what or how I get you what you need.

Chris

Rick Deskins
Thermwood Team
Posts: 837
Joined: Tue, May 17 2005, 12:47PM
Company Name: Thermwood
Country: UNITED STATES
Location: Thermwood

Re: drawer box front for pull-outs

Postby Rick Deskins » Mon, Jun 11 2012, 10:26AM

I need either the ecabinets job file (ESJ), cabinet file (HSF), or asssembly file (ESA) that was used to create the twd file.
Rick Deskins
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900

Chris B Campbell
Junior Member
Posts: 84
Joined: Fri, Jul 29 2005, 4:00PM
Location: Helendale, CA.

Re: drawer box front for pull-outs

Postby Chris B Campbell » Mon, Jun 11 2012, 10:40AM

Hope this works
Attachments
Draws.jpg
Draws.jpg (7.75 KiB) Viewed 2270 times
Draws.esa
(1.68 MiB) Downloaded 57 times

Rick Deskins
Thermwood Team
Posts: 837
Joined: Tue, May 17 2005, 12:47PM
Company Name: Thermwood
Country: UNITED STATES
Location: Thermwood

Re: drawer box front for pull-outs

Postby Rick Deskins » Mon, Jun 11 2012, 10:52AM

Well, I tested your file going out to control nesting and all worked for me. So, there must be a setting on your control nesting that would produce this. I will need to get the export from your control nesting. Go to control nesting and load the twd you are having problem with. the go to file->Export and save off the export file. It will be a *.cab file. Then post that and hopefully we can find the root of your problem.
Rick Deskins
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900

Chris B Campbell
Junior Member
Posts: 84
Joined: Fri, Jul 29 2005, 4:00PM
Location: Helendale, CA.

Re: drawer box front for pull-outs

Postby Chris B Campbell » Mon, Jun 11 2012, 11:45AM

???? << Go to control nesting and load the twd you are having problem with. the go to file->Export>>>???
Okay, Load file, bottom of screen F5 (File) there is no export button? I can save a file (F2) but it is the CNC file.

Chris B Campbell
Junior Member
Posts: 84
Joined: Fri, Jul 29 2005, 4:00PM
Location: Helendale, CA.

Re: drawer box front for pull-outs

Postby Chris B Campbell » Mon, Jun 11 2012, 11:49AM

$&*(^*)_(@#.... MONDAY MORNING!!!

Here Ya Go.

Chris B Campbell
Junior Member
Posts: 84
Joined: Fri, Jul 29 2005, 4:00PM
Location: Helendale, CA.

Re: drawer box front for pull-outs

Postby Chris B Campbell » Mon, Jun 11 2012, 11:50AM

Well it wont allow the .cab extension

Rick Deskins
Thermwood Team
Posts: 837
Joined: Tue, May 17 2005, 12:47PM
Company Name: Thermwood
Country: UNITED STATES
Location: Thermwood

Re: drawer box front for pull-outs

Postby Rick Deskins » Mon, Jun 11 2012, 11:52AM

Can you email the cab file to cabinets@thermwood.com?
Rick Deskins
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900


Return to “eCabinet Systems Software”

Who is online

Users browsing this forum: Bing [Bot] and 9 guests