Display panels on end of cabinet?
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal
-
- Junior Member
- Posts: 85
- Joined: Fri, Feb 16 2007, 2:00PM
Display panels on end of cabinet?
I don't know how I ended up with display panels on the sides of this cabinet, but I can't get rid of them. I've taken it into the cabinet editor, tried delete, tried a texture match. I could shuffle it by, but the different color sticks out like a sore thumb in the presentation mode. Any ideas?
The only DUMB question is the one you don't ask!
-
- Thermwood Team
- Posts: 1740
- Joined: Tue, May 17 2005, 12:44PM
- Company Name: Thermwood Corporation
- Location: Thermwood Corp: Dale, Indiana
- Contact:
Re: Display panels on end of cabinet?
George,
Post the job and some steps and we will look at it. Zip the job before you post it or if you have trouble posting it, send it to cabinets@thermwood.com .
Post the job and some steps and we will look at it. Zip the job before you post it or if you have trouble posting it, send it to cabinets@thermwood.com .
Regards,
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000
-
- Thermwood Team
- Posts: 857
- Joined: Tue, May 17 2005, 12:47PM
- Company Name: Thermwood
- Country: UNITED STATES
- Location: Thermwood
Re: Display panels on end of cabinet?
Are there applied ends? In the cabinet editor, right click and choose add/remove applied ends. Check both and remove applied ends and you should be good to go.
Rick Deskins
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900
-
- Junior Member
- Posts: 85
- Joined: Fri, Feb 16 2007, 2:00PM
Re: Display panels on end of cabinet?
Scott
Same PITA file I sent you before. It's the cabinet over the refrigerator.
Rick
I did that too then I didn't have any sides on it at all.
I finally fixed the problem, I deleted the whole cabinet and started over. Now it's right
I do have another question though. If I set my board stock to say, white; why can't I build my doors from the selected materials? I ended up picking the "maple with the white ivory sheen". Then I had to do a texture match to get what I wanted. Is there some way to add a material choice to that "Standard" section?
Same PITA file I sent you before. It's the cabinet over the refrigerator.
Rick
I did that too then I didn't have any sides on it at all.
I finally fixed the problem, I deleted the whole cabinet and started over. Now it's right
I do have another question though. If I set my board stock to say, white; why can't I build my doors from the selected materials? I ended up picking the "maple with the white ivory sheen". Then I had to do a texture match to get what I wanted. Is there some way to add a material choice to that "Standard" section?
The only DUMB question is the one you don't ask!
-
- Junior Member
- Posts: 85
- Joined: Fri, Feb 16 2007, 2:00PM
Re: Display panels on end of cabinet?
I have another question too. Why doesn't it build the side wall of the cabinet so that it's the same length as the face frame? Is there some way to edit the length of that side wall? Upper cabinets sometimes have under the cabinet lighting. If the side isn't equal to the face frame then the lighting is exposed.
The only DUMB question is the one you don't ask!