Can't see numbers in detal room view

Greg Michael · Post by **Greg Michael** » Tue, Aug 21 2007, 1:39PM

I am working on a lagre kitchen and when I place my cabinets, they are small. I need to know distances between them and the numbers are very small. I can't read them, and I cannot figure out a way to voom in. Can anyone help me?

Michael Rice · Post by **Michael Rice** » Tue, Aug 21 2007, 2:19PM

Greg
Use the + key to zoom in, and - to zoom out. Use the arrow keys to move the image around.
Mike

Greg Michael · Post by **Greg Michael** » Tue, Aug 21 2007, 2:38PM

Mike thank you so much! I knew it had to be somthing simple...

Greg

Michael Rice · Post by **Michael Rice** » Tue, Aug 21 2007, 2:54PM

You're welcome Greg.....it's the simple things I usually miss too. How's the heat up in Canton........It was 100 at lake oconee today.

Mike

Dennis Englert · Post by **Dennis Englert** » Tue, Aug 21 2007, 3:05PM

In the plan view, hold the control (CTRL) key down and drag a window around the area that you need to zoom in on.

Drag a window by left clicking in an imaginary corner of the window and then left clicking in the opposite corner of the window.

Dennis Englert · Post by **Dennis Englert** » Tue, Aug 21 2007, 3:26PM

In the plan view, hold the control (CTRL) key down and drag a window around the area that you need to zoom in on.

Drag a window by left clicking in an imaginary corner of the window and then left clicking in the opposite corner of the window.

Michael Rice · Post by **Michael Rice** » Tue, Aug 21 2007, 3:36PM

Hey Dennis
Thanks for the tip. Guess that's why you're the teacher.....you know all the tricks !

Mike

DanEpps · Post by **DanEpps** » Tue, Aug 21 2007, 5:30PM

Michael Rice wrote:...How's the heat up in Canton........It was 100 at lake oconee today...

Same up here is Rocky Face

In fact, we are looking forward to cooling down to 95 later this week. Our swimming pool has been over 90 for that last couple of weeks so there is no refuge there either.

Michael Rice · Post by **Michael Rice** » Tue, Aug 21 2007, 5:51PM

Yeah Dan.....I know what you mean by no refuge. My shop is a steel building with no air except in the office. I'm working 5:30 to 1:30 during this heat.......that's my refuge.

Mike

Greg Michael · Post by **Greg Michael** » Wed, Aug 22 2007, 4:10AM

Thanks Dennis

As for the heat... We are melting here in Canton as well... Spray booth is not alot of fun in 100+ weather. We could use some rain too.

Greg

George Davidson · Post by **George Davidson** » Wed, Aug 22 2007, 6:54AM

You can have soom of our rain
It started raining last Sat. still raining and hard the hole time
On the line of Pa. and De. to much rain now

It is in the high 60 now they say it will be back in the 90's Sat.

Greg Michael · Post by **Greg Michael** » Wed, Aug 22 2007, 9:01AM

OK We will take it... just a little at a time though...

DanEpps · Post by **DanEpps** » Wed, Aug 22 2007, 9:21AM

Greg Michael wrote:OK We will take it... just a little at a time though...

No kidding...we haven't had a drop of rain since late July. We can only use water outside 3 days a week between midnight and 10am and they are talking about cutting it back to just 1 day a week, closing carwashes, etc.

Thermwood / eCabinet Systems

Can't see numbers in detal room view

Can't see numbers in detal room view

Re:

Re: