A frameless blind basecab is the today's challenge cup, and the file is attached.
The door has a 1/8" margin between itself and it's "stile" on the left, which is the spec for the Blum blind corner hinges used there.
Bottom reveal is zero, top reveal is 3/8", R side reveal is 1/8".
Take the cabinet, remove the door, and replace it so that you get the same reveals. It is a "faceframed" cab, with the only part of the faceframe being the 4" "stile" the door is hinged to, thus the door is inset 3/4".
I'll start the timer when you've loaded the file.
Test: place the door with the fewest keystrokes
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal
Test: place the door with the fewest keystrokes
- Attachments
-
- LH blind base.hsf
- (454.02 KiB) Downloaded 254 times
-
- Wizard Member
- Posts: 4723
- Joined: Mon, May 09 2005, 7:33PM
- Company Name: Double E Cabinets
- Country: UNITED STATES
- Location: Amarillo, TX
Re: Test: place the door with the fewest keystrokes
Gene,
What seems to be the problem? Once you save your file with the door parameters there is no problem changing doors.
Kerry
What seems to be the problem? Once you save your file with the door parameters there is no problem changing doors.
Kerry
Re: Test: place the door with the fewest keystrokes
Load it up and go to work, Kerry.
Let's see what you need to do to get the job done.
Let's see what you need to do to get the job done.
-
- Wizard Member
- Posts: 4723
- Joined: Mon, May 09 2005, 7:33PM
- Company Name: Double E Cabinets
- Country: UNITED STATES
- Location: Amarillo, TX
Re: Test: place the door with the fewest keystrokes
I did it before the last post.
3/4 inset
+1/8" Hinge side gap
-5/8" Open side gap
-3/8" Top gap
-3/4" bottom gap
I still don't know what you are trying to get at.
Kerry
3/4 inset
+1/8" Hinge side gap
-5/8" Open side gap
-3/8" Top gap
-3/4" bottom gap
I still don't know what you are trying to get at.
Kerry
- Attachments
-
- gene_08.jpg (38.24 KiB) Viewed 4285 times
-
- eCabinets Beta Tester
- Posts: 923
- Joined: Wed, Apr 05 2006, 5:50PM
- Location: Marion, Ar.
- Contact:
Re: Test: place the door with the fewest keystrokes
Not sure what the problem is, changed doors for ya
- Attachments
-
- iiii.jpg (20.99 KiB) Viewed 4322 times
-
- iiii.hsf
- (400.02 KiB) Downloaded 276 times
Damon Nabors
-
- Senior Member
- Posts: 151
- Joined: Wed, May 18 2005, 10:00AM
- Company Name: Expressions in Wood
- Country: UNITED STATES
- Location: FLEMINGTON
Re: Test: place the door with the fewest keystrokes
Took about 5 minutes because I didn't get the constructions settings on the first try.
Hinge side gap: -.75"
Open side gap: .125"
Top gap: -.375"
Bottom gap: -.75"
Door inset: .75
Good practice. Thanks
Glenn
Hinge side gap: -.75"
Open side gap: .125"
Top gap: -.375"
Bottom gap: -.75"
Door inset: .75
Good practice. Thanks
Glenn
-
- eCabinets Beta Tester
- Posts: 923
- Joined: Wed, Apr 05 2006, 5:50PM
- Location: Marion, Ar.
- Contact:
Re: Test: place the door with the fewest keystrokes
What happened to Gene, did his timer break?
Damon Nabors