Problems with Drawers in 5.2
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal
-
- Guru Member
- Posts: 406
- Joined: Tue, May 17 2005, 12:41PM
- Location: In the Boonies near Oromocto, NB, Canada
Problems with Drawers in 5.2
This unit worked fine in 5.1 but now, when I try to change drawers, it gives me a steady increment in the size of the drawer front depending on which one I insert first, second and last. It increases in size in that order. I even tried starting with the middle one and still the same thing.
Can someone make head or tail of this? Could be a bug I guess and will need to be addressed.
Thanks
Can someone make head or tail of this? Could be a bug I guess and will need to be addressed.
Thanks
- Attachments
-
- Angled Island - Ctr Cab.jpg (10.84 KiB) Viewed 9820 times
-
- Angled Island - Ctr Cab.hsf
- (1.18 MiB) Downloaded 290 times
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Problems with Drawers in 5.2
The drawer boxes and fronts work ok in there own editor, it's when you take it to main that it all flies apart.
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Problems with Drawers in 5.2
I just tried one from scratch and it locks up when I try to go into the DBE.
-
- Guru Member
- Posts: 406
- Joined: Tue, May 17 2005, 12:41PM
- Location: In the Boonies near Oromocto, NB, Canada
Re: Problems with Drawers in 5.2
So I guess it is not just me. Good in a way, I feel better LOL but it looks like it is a bug now.
-
- Guru Member
- Posts: 269
- Joined: Sun, Apr 29 2007, 8:53PM
- Company Name: Creative Kitchens and Interior
- Country: NEW ZEALAND
- Location: Tauranga New Zealand
Re: Problems with Drawers in 5.2
i ACTUALLY HAD A DOUBLE BANK OF 6 DRWS A SIDE AND WENT TO THE EDITOR TO CHANGE THE REVEAL ON THE OUTER RIGHT SIDE FROM A 2MM GAP TO A 1MM GAP.HIGHLIGHTED ALL DRWS ON RIGHT WENT TO CONSTRUCTION SETTINGS AND RESET THE REVEAL FROM 2MM TO 1MM PRESSED ENTER AND IT SHIFTED ALL THE DRAWER FRONTS UPWARDS.DID IT 3 TIMES AND ENDED UP DELETING ALL THE DRAWERS AND STARTING AGAIN.
-
- Guru Member
- Posts: 406
- Joined: Tue, May 17 2005, 12:41PM
- Location: In the Boonies near Oromocto, NB, Canada
Re: Problems with Drawers in 5.2
I have tried re-starting this one over and over. Every time, the drawer act this way. Maybe the wizards can find a fix or work around for this.
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Problems with Drawers in 5.2
Can you use a standard cab instead of a corner?
Re: Problems with Drawers in 5.2
I’ve got this listed for the programmers. If you remove the FF and uncheck “left and right sides miter” from the corner settings then reapply your FF the drawers should work.
Sorry for the inconvenience.
Sorry for the inconvenience.
-
- Guru Member
- Posts: 406
- Joined: Tue, May 17 2005, 12:41PM
- Location: In the Boonies near Oromocto, NB, Canada
Re: Problems with Drawers in 5.2
No Rick I can not use something else in that position.
Thanks Walker, I will try that when I get home tonight and post my findings.
Cheers
Thanks Walker, I will try that when I get home tonight and post my findings.
Cheers
-
- Guru Member
- Posts: 406
- Joined: Tue, May 17 2005, 12:41PM
- Location: In the Boonies near Oromocto, NB, Canada
Re: Problems with Drawers in 5.2
Well, that fixed the drawer issue but screwed up the back as you can see in the attached image. The left side is now 1/4" wider the the right side. Nothing I seem to be able to do to fix that either.
Re: Problems with Drawers in 5.2
Denis
Are you saying that you can not remove the ¼ back inset for the left end in construction settings?
Are you saying that you can not remove the ¼ back inset for the left end in construction settings?
-
- Guru Member
- Posts: 406
- Joined: Tue, May 17 2005, 12:41PM
- Location: In the Boonies near Oromocto, NB, Canada
Re: Problems with Drawers in 5.2
Yes Walker....that is what is happening. The inset just popped after the drawers were fixed but in my settings, I can not find anywhere a inset for that sides, back or deck. Not sure where else to look.
Re: Problems with Drawers in 5.2
This is another bug related to “left and right sides mitre” I believe. See if unchecking that helps.
-
- Junior Member
- Posts: 58
- Joined: Sat, Aug 13 2005, 4:21PM
- Location: Arkansas
Re: Problems with Drawers in 5.2
this maybe a old bug but just had it happen I resized a base cabinet and went from 48" to 52" and all went well.
But when I move the Mid Stile the Drawer boxes resized to fit the cabinet but the doors and the drawer did not
resizes.
But when I move the Mid Stile the Drawer boxes resized to fit the cabinet but the doors and the drawer did not
resizes.
Re: Problems with Drawers in 5.2
Beckham
Could you attach the cabinet and will take a look.
Thanks
Could you attach the cabinet and will take a look.
Thanks