Reinstall
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal
-
- Junior Member
- Posts: 44
- Joined: Mon, Mar 13 2006, 6:35PM
- Location: Sussex WI
Reinstall
I reformatted the hard drive, turned off my antivires and tried to install eCabinets and get the following error,
1305.Error reading from C:\Program Files\Thermwood\eCabinet Systems\hoops1106.dll. Verify that the files exists and that you can acces it. I have a M70, cleaned the disk(Version 5), tried to reinstall with the same error.
Thanks for helping with the reinstall.
Douglas Walters
1305.Error reading from C:\Program Files\Thermwood\eCabinet Systems\hoops1106.dll. Verify that the files exists and that you can acces it. I have a M70, cleaned the disk(Version 5), tried to reinstall with the same error.
Thanks for helping with the reinstall.
Douglas Walters
D Walters
Wood Architects
Wood Architects
-
- Thermwood Team
- Posts: 857
- Joined: Tue, May 17 2005, 12:47PM
- Company Name: Thermwood
- Country: UNITED STATES
- Location: Thermwood
Re: Reinstall
After installing from the disc, you need to install the latest patch.
http://downloads.thermwood.com/eCabinet ... uild-2.exe
http://downloads.thermwood.com/eCabinet ... uild-2.exe
Rick Deskins
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900
eCabinet Systems Programmer
Dell Precision / Xeon E3-1240 / 8GB RAM/ AMD FirePro V4900
-
- Junior Member
- Posts: 44
- Joined: Mon, Mar 13 2006, 6:35PM
- Location: Sussex WI
Re: Reinstall
Hi Rick,
The error comes up before it finishes the install from the disk. I can't even think about updating yet.
Thanks,
Douglas Walters
The error comes up before it finishes the install from the disk. I can't even think about updating yet.
Thanks,
Douglas Walters
D Walters
Wood Architects
Wood Architects
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Reinstall
Douglas, try updating or reinstalling the drivers for your CD-ROM or DVD drive.
-
- Junior Member
- Posts: 44
- Joined: Mon, Mar 13 2006, 6:35PM
- Location: Sussex WI
Re: Reinstall
Thanks Rick,
Updated the firmware, uninstalled AVG, rebooted, tried to reinstall ecab, 80% done and a different error 1305 comes up.
Errorreading from file C:\Program Files\Thermwood\eCabinet Systems\hardware\Wood Components\Hafele\Hf-194-78-335.hsf. Verify that the file exists and that you can acces it. Retry or cancel. Retry comes up with the same error.
The Hafele component should be on the disk.
What should my next step be?
I retried and it is the same as above except says .jpg.
Where would I verify this exists?
Updated the firmware, uninstalled AVG, rebooted, tried to reinstall ecab, 80% done and a different error 1305 comes up.
Errorreading from file C:\Program Files\Thermwood\eCabinet Systems\hardware\Wood Components\Hafele\Hf-194-78-335.hsf. Verify that the file exists and that you can acces it. Retry or cancel. Retry comes up with the same error.
The Hafele component should be on the disk.
What should my next step be?
I retried and it is the same as above except says .jpg.
Where would I verify this exists?
D Walters
Wood Architects
Wood Architects
-
- Wizard Member
- Posts: 5852
- Joined: Thu, Jul 28 2005, 10:18AM
- Company Name: Dan Epps
- Country: UNITED STATES
- Location: Rocky Face GA
Re: Reinstall
Try uninstalling eCabinets before starting the reinstall.
Are you running Vista? If so, make sure you are following the Vista installation instructions in the sticky at the top of the forum.
Are you running Vista? If so, make sure you are following the Vista installation instructions in the sticky at the top of the forum.
-
- Junior Member
- Posts: 44
- Joined: Mon, Mar 13 2006, 6:35PM
- Location: Sussex WI
Re: Reinstall
Hi Dan,
eCab has not been installed on this after the reformat. I am running XP and have checked the add/remove programs and there is nothing to remove.
eCab has not been installed on this after the reformat. I am running XP and have checked the add/remove programs and there is nothing to remove.
D Walters
Wood Architects
Wood Architects
-
- Junior Member
- Posts: 44
- Joined: Mon, Mar 13 2006, 6:35PM
- Location: Sussex WI
Re: Reinstall
Hey Guy's,
Can anyone from Thermwood help out? I need to get this installed.
Thanks
Can anyone from Thermwood help out? I need to get this installed.
Thanks
D Walters
Wood Architects
Wood Architects
Re: Reinstall
Doug
Try to download the latest update first from the internet. I know that you do not have the software installed yet but I am thinking since it is a version 5 disk, if you download the update frist and run it then try to install the cd. If this does not work you can email me, call, or post back on here.
Try to download the latest update first from the internet. I know that you do not have the software installed yet but I am thinking since it is a version 5 disk, if you download the update frist and run it then try to install the cd. If this does not work you can email me, call, or post back on here.