Edgebanding Deck
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Edgebanding Deck
The system is not allowing me to edgeband the deck on this cab. Any idea's?
- Attachments
-
- Tall Closet TV.hsf
- (692.02 KiB) Downloaded 283 times
-
- eCabinets Beta Tester
- Posts: 923
- Joined: Wed, Apr 05 2006, 5:50PM
- Location: Marion, Ar.
- Contact:
Re: Edgebanding Deck
Rick, here is your cabinet w/edgebanding.
Damon
Damon
- Attachments
-
- Tall Closet TV.hsf
- (692.02 KiB) Downloaded 273 times
Damon Nabors
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Edgebanding Deck
What ya do?
-
- eCabinets Beta Tester
- Posts: 923
- Joined: Wed, Apr 05 2006, 5:50PM
- Location: Marion, Ar.
- Contact:
Re: Edgebanding Deck
deleted the toe kick and the deck. Reloaded the deck. Applied the edgebanding and then reloaded the toe kick. It would not take the edgebanding as long as the toe kick was there. I ran into a problem like this the other day but finally got it to work.
Sorry, I didn't explain earlier, the wife was informing me that I needed to get off the computer. Imagine that!
Damon
Sorry, I didn't explain earlier, the wife was informing me that I needed to get off the computer. Imagine that!
Damon
Damon Nabors
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Edgebanding Deck
I get that issue sometimes too.
-
- eCabinets Beta Tester
- Posts: 923
- Joined: Wed, Apr 05 2006, 5:50PM
- Location: Marion, Ar.
- Contact:
Re: Edgebanding Deck
Rick, I am working on a large edgebanding job myself and this edge banding thing is all new to me since we normally only do FF cabs.
I guess you can not edge band a stretcher??? I noticed that stretchers do not show up on the list.
Damon
I guess you can not edge band a stretcher??? I noticed that stretchers do not show up on the list.
Damon
Damon Nabors
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Edgebanding Deck
I use a fixed shelf with a back inset instead of a stretcher.
-
- eCabinets Beta Tester
- Posts: 923
- Joined: Wed, Apr 05 2006, 5:50PM
- Location: Marion, Ar.
- Contact:
Re: Edgebanding Deck
I have never tried it, but if I understand you correct, your saying you can rotate a shelf into position to act as a toe kick, or toe board??
Damon Nabors
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Edgebanding Deck
No, you can't rotate a shelf. In frameless, a stretcher is commonly used between drawer openings.
-
- eCabinets Beta Tester
- Posts: 923
- Joined: Wed, Apr 05 2006, 5:50PM
- Location: Marion, Ar.
- Contact:
Re: Edgebanding Deck
My bad, I thought you was talking about the toekick. I know what you are talking about with the shelf. I used one like that the other day. I guess you got everything worked out and ready to cut now.
Good luck,
Damon
Good luck,
Damon
Damon Nabors
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Edgebanding Deck
Yes, we are sending this job out for a price on getting it cut.
Re: Edgebanding Deck
I’ve been looking at your cabinet Rick and the front construction on the deck is blank in the construction settings. If you change it to butt and press ok you should be good to go. Do you or Damon know what you did to get this to happen I can’t reproduce this?
-
- Wizard Member
- Posts: 1896
- Joined: Wed, May 18 2005, 7:54PM
- Company Name: Milltech Millworks Ltd.
- Country: CANADA
- Location: Edmonton, Alberta
- Contact:
Re: Edgebanding Deck
I will try and reproduce it Walker.
-
- eCabinets Beta Tester
- Posts: 923
- Joined: Wed, Apr 05 2006, 5:50PM
- Location: Marion, Ar.
- Contact:
Re: Edgebanding Deck
Walker, I don't recall looking to see if BUTT was checked or not, but the deck did not show up in the edge banding list. I had to delete the deck and add it back in order to get the deck edgebanding to show up on the list of parts to be edgebanded.
Damon
Damon
Damon Nabors
-
- eCabinets Beta Tester
- Posts: 923
- Joined: Wed, Apr 05 2006, 5:50PM
- Location: Marion, Ar.
- Contact:
Re: Edgebanding Deck
That worked pretty good also Walker, the front edge of the deck was blank on my screen but I changed it to Butt and everything works ok.
I guess we need to dbl check and then dbl check again.
I guess we need to dbl check and then dbl check again.
Damon Nabors