Drawers in blank corner cabinet

Moderators: Jason Susnjara, Clint Buechlein

User avatar
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Drawers in blank corner cabinet

Postby George Davidson » Fri, Mar 09 2007, 9:33AM

Has anyone put drawers in the back of a blank corner cabinet.
If so did your customer have any remarks about it.

Now that I look at the picture I think the sides of the drawers are to
high. They are 6 in high now?

greg youngken
Senior Member
Posts: 103
Joined: Wed, Jan 10 2007, 9:53PM
Company Name: Grali inc.
Location: lilburn,ga
Contact:

Postby greg youngken » Fri, Mar 09 2007, 7:20PM

Interesting, I use a double swivel out of blind corner, then slide out of cabinet shelf system. Hope this is not a double post, my other one just seemed to vanish?
Grali inc. / Greg Youngken
grali.com

User avatar
Kerry Fullington
Wizard Member
Posts: 4566
Joined: Mon, May 09 2005, 7:33PM
Company Name: ProSource of Amarillo
Country: UNITED STATES
Location: Amarillo, TX

Postby Kerry Fullington » Fri, Mar 09 2007, 8:38PM

George,
Wouldn't you lose the storage space in front of the drawer so they could slide out? So you wouldn't really gain anything.
Kerry

User avatar
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Postby George Davidson » Fri, Mar 09 2007, 8:58PM

Kerry That is right :wall:

Lamar Horton
Senior Member
Posts: 222
Joined: Sun, Dec 11 2005, 1:22PM
Location: Kennedale, Texas
Contact:

Postby Lamar Horton » Fri, Mar 09 2007, 10:52PM

Unless you had a pull out in front of the back drawers and raised the back drawers up a little to clear the slides of the front drawer.

Nemanja Vujkovic
Senior Member
Posts: 222
Joined: Wed, Feb 21 2007, 1:29PM
Location: STL, MO

Postby Nemanja Vujkovic » Sat, Mar 10 2007, 1:34AM

That's actuly good idea. I did a job that was resolved in similar matter.
However it was not done on eCabinets, or cnc.

User avatar
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Postby George Davidson » Sat, Mar 10 2007, 6:35AM

That will work
Thank You Lamar
Attachments
B-2_Drawers in corner.jpg
B-2_Drawers in corner.jpg (79.33 KiB) Viewed 1345 times

Lamar Horton
Senior Member
Posts: 222
Joined: Sun, Dec 11 2005, 1:22PM
Location: Kennedale, Texas
Contact:

Postby Lamar Horton » Sat, Mar 10 2007, 11:23AM

I have been pondering a solution for this situation for a long time and was not able to come up with simple answer. All of the pre-fabed insets for corner cabinets are outragesly priced, although I see why. I have dreamed up some pretty elaborate contraptions that, in reality, would probably not hold up over time. It wasn't until I saw your drawing that the light went on. Thanks


Return to “Customer Images”

Who is online

Users browsing this forum: No registered users and 3 guests