Range Hoods and Valances

Moderators: Jason Susnjara, Clint Buechlein

andy Schermerhorn
New Member
Posts: 6
Joined: Tue, May 18 2010, 11:36AM
Company Name: precision built

Range Hoods and Valances

Postby andy Schermerhorn » Tue, May 18 2010, 1:00PM

Hello I am new to eCabinets and have some questions. I need to design a range hood and valance like the ones that conestoga sells. What is the best way of doing this? The range hood I tried to make as an assembly then attach the different parts together to get the desired effect, but was not able to do so.Any input here would be great. Mainly having a problem with the angled parts of the hood.
Thanks

User avatar
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Postby George Davidson » Tue, May 18 2010, 3:30PM

Hi Andy
If you put in Range Hood in Searh on the top of page. You will get some range hoods.
Do you have a picture of the one you want

andy Schermerhorn
New Member
Posts: 6
Joined: Tue, May 18 2010, 11:36AM
Company Name: precision built

Re: Range Hoods and Valances

Postby andy Schermerhorn » Wed, May 19 2010, 8:21AM

What I am trying to create is a range hood with slanted front that starts at 12"deep at the top and goes to 18" deep at the bottom with three raised panels on the angled face. Below the angled face is a ledge like a mantle with trim under it, and a curved raised panel valance below that. If this makes any sense to anyone besides me, I dont know. The cabinet needs to be 42" w x 32"h x 20" deep overall. Not sure how far off the top of the range the hood needs to be, at 32"h the panel would be 28" off the range.

User avatar
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Postby George Davidson » Wed, May 19 2010, 11:27AM

I am not sure if this is what you are looking for.Before I do any more to it
Attachments
Hood-t.jpg
Hood-t.jpg (20.16 KiB) Viewed 9707 times
Range Hood 42 W x 32 H x 20 D.jpg
Range Hood 42 W x 32 H x 20 D.jpg (42.59 KiB) Viewed 9352 times

andy Schermerhorn
New Member
Posts: 6
Joined: Tue, May 18 2010, 11:36AM
Company Name: precision built

Re: Range Hoods and Valances

Postby andy Schermerhorn » Wed, May 19 2010, 1:21PM

This is close, thank you for helping me I have more problems then I can handle. The sides of it are flat not angled, to fit between to cabinets. The only angle is the front where the paneling would be. Thank you for the help, I take it that that did not come from ecab.

User avatar
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Postby George Davidson » Wed, May 19 2010, 1:55PM

Here is one I made before
42" x 24" x 19"
Attachments
42 x 24 x 19 D.esa
(554.02 KiB) Downloaded 501 times
42 x 24 x 19 D.jpg
42 x 24 x 19 D.jpg (16.51 KiB) Viewed 9702 times

andy Schermerhorn
New Member
Posts: 6
Joined: Tue, May 18 2010, 11:36AM
Company Name: precision built

Re: Range Hoods and Valances

Postby andy Schermerhorn » Wed, May 19 2010, 3:29PM

That is what I need thank you. One more question so I get this right, I take that esa file and download it to the assemblies library?

User avatar
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Postby George Davidson » Wed, May 19 2010, 3:49PM

Yes I put it in a folder and then assemblies library

Lubert Willis
New Member
Posts: 1
Joined: Tue, Apr 17 2012, 7:37AM
Company Name: Precision Greenwood
Country: UNITED STATES

Re: Range Hoods and Valances

Postby Lubert Willis » Tue, Apr 17 2012, 7:54AM

George Davidson wrote:I am not sure if this is what you are looking for.Before I do any more to it

Thank you George. This is what I was looking for!
This is great website where you will find all kinds of best range hoods.

User avatar
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Postby George Davidson » Tue, Apr 17 2012, 12:24PM

Hi Lubert
OK
Can you put trim on it


Return to “Customer 3D Files”

Who is online

Users browsing this forum: No registered users and 3 guests