Need a registration code

Off-topic discussion that doesn't pertain to the other forums.

Moderator: Jason Susnjara

Post Reply
Denis L'Heureux
Guru Member
Posts: 406
Joined: Tue, May 17 2005, 12:41PM
Location: In the Boonies near Oromocto, NB, Canada

Need a registration code

Post by Denis L'Heureux »

It says I am at my limit for my email. Can you reset this or send me one please?

Tx
Image
Brad McIntosh
Guru Member
Posts: 559
Joined: Wed, May 18 2005, 6:59PM
Company Name: CNC Automation
Country: CANADA
Location: St. Zotique, Québec, Canada
Contact:

Re: Need a registration code

Post by Brad McIntosh »

Denis,

You should either contact us at CNC Automation OR email cabinets@thermwood.com with your reset request.

The forum areas are not always the best method to use when a quick response is required to a specific issue.


----------------------------------------------------------------------------------------
Questions de «support au logiciel»??
Envoyez-nous un courriel à <logiciel@cncautomation.com>
ou
Appelez-nous @ 1-800-421-5955 et demandez à
parler avec un représentant de support au logiciel.
----------------------------------------------------------------------------------------
Software Support Questions??
Email us at <software@cncautomation.com>
or
Call us @ 1-800-421-5955 and ask to speak
with a software support representative.
----------------------------------------------------------------------------------------
Brad McIntosh
CNC Automation

Home: http://www.cncautomation.com
Twitter: @bmcncautomation
Denis L'Heureux
Guru Member
Posts: 406
Joined: Tue, May 17 2005, 12:41PM
Location: In the Boonies near Oromocto, NB, Canada

Re: Need a registration code

Post by Denis L'Heureux »

I already requested via email but never received anything I'll try again I guess
Image
Denis L'Heureux
Guru Member
Posts: 406
Joined: Tue, May 17 2005, 12:41PM
Location: In the Boonies near Oromocto, NB, Canada

Re: Need a registration code

Post by Denis L'Heureux »

It is just not working. I can't get anything via email. There must be a way that I can use this software again.
Image
Brad McIntosh
Guru Member
Posts: 559
Joined: Wed, May 18 2005, 6:59PM
Company Name: CNC Automation
Country: CANADA
Location: St. Zotique, Québec, Canada
Contact:

Re: Need a registration code

Post by Brad McIntosh »

Denis,

First check you SPAM or JUNK MAIL folder....

If there is nothing there - PLEASE CONTACT US HERE @ CNC AUTOMATION

----------------------------------------------------------------------------------------
Questions de «support au logiciel»??
Envoyez-nous un courriel à <logiciel@cncautomation.com>
ou
Appelez-nous @ 1-800-421-5955 FREE et demandez à
parler avec un représentant de support au logiciel.
----------------------------------------------------------------------------------------
Software Support Questions??
Email us at <software@cncautomation.com>
or
Call us @ 1-800-421-5955 FREE and ask to speak
with a software support representative.
----------------------------------------------------------------------------------------
Brad McIntosh
CNC Automation

Home: http://www.cncautomation.com
Twitter: @bmcncautomation
Brad McIntosh
Guru Member
Posts: 559
Joined: Wed, May 18 2005, 6:59PM
Company Name: CNC Automation
Country: CANADA
Location: St. Zotique, Québec, Canada
Contact:

Re: Need a registration code

Post by Brad McIntosh »

Denis,

I sent an email to Thermwood and they replied that your Code Generator account should be reset. Please go and try to request a new code...

http://order.ecabinetsystems.com/ecabfo ... ubmit.aspx

Hope it works and that you have a great weekend!
Brad McIntosh
CNC Automation

Home: http://www.cncautomation.com
Twitter: @bmcncautomation
Brad McIntosh
Guru Member
Posts: 559
Joined: Wed, May 18 2005, 6:59PM
Company Name: CNC Automation
Country: CANADA
Location: St. Zotique, Québec, Canada
Contact:

Re: Need a registration code

Post by Brad McIntosh »

Just so everyone can relax over the weekend...

Thanks to Mike @ Thermwood's software support department, Denis' Code Generator Account was reset and he now has his new code. (He was starting to go through eCabinet Systems withdrawal. :wink: )

Hope everyone has a great weekend!
Brad McIntosh
CNC Automation

Home: http://www.cncautomation.com
Twitter: @bmcncautomation
Post Reply