I've been having issues for the past few months with CN (6.07 on THM desktop) locking up when I have a job nested and change the offfall setting (to either None or Cut Full Perimeter.)
Just installed CN 6.08, and it no longer locks up when I change the offfall setting. However, it's not acting right: If offfall is turned off when I nest a job, there will be no offfall in the nest, as expected. If I turn offfall on, the offfall appears in the nest, as expected. But if I then turn the offfall off again, it won't go away, it stays on. Anyone else having this?
Offfall setting in CN
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Jim Bullis
-
- eCabinets Beta Tester
- Posts: 1119
- Joined: Tue, May 10 2005, 9:36PM
- Company Name: Corlane Custom Cabinetry LLC
- Country: UNITED STATES
- Location: Carnesville, GA
- Contact:
Offfall setting in CN
http://www.corlanecabinetry.com
Intel Core i7-5820 3.3GHz, 16GB RAM, NVidia Quadro K2200 4GB, Windows 8.1 Pro 64 bit
CS-41 4x8
CS-45 5x12
Intel Core i7-5820 3.3GHz, 16GB RAM, NVidia Quadro K2200 4GB, Windows 8.1 Pro 64 bit
CS-41 4x8
CS-45 5x12
-
- Guru Member
- Posts: 293
- Joined: Fri, Jul 27 2012, 12:30PM
- Company Name: true form cabinets
- Country: CANADA
- Contact:
Re: Offfall setting in CN
I just tried that no issues. are you sure its not a settings grouping issue? try with ignore settings grouping checked off
Intel(R) Core(TM) i5-6400 @ 2.70GHz 8.00 GB RAM
NVIDIA GeForce GTX 950
Windows 10 Professional 64-bit
http://www.trueform.ca
CS43 cnc
NVIDIA GeForce GTX 950
Windows 10 Professional 64-bit
http://www.trueform.ca
CS43 cnc
-
- Guru Member
- Posts: 559
- Joined: Wed, May 18 2005, 6:59PM
- Company Name: CNC Automation
- Country: CANADA
- Location: St. Zotique, Québec, Canada
- Contact:
Re: Offfall setting in CN
Are you Nesting/Optimizing and THEN changing the settings. If so, perhaps try re-nesting. (??)
-
- eCabinets Beta Tester
- Posts: 1119
- Joined: Tue, May 10 2005, 9:36PM
- Company Name: Corlane Custom Cabinetry LLC
- Country: UNITED STATES
- Location: Carnesville, GA
- Contact:
Re: Offfall setting in CN
I'm linking a video that makes it more clear (I hope)... but in a nutshell, I can set offfall to "None" and nest it, then turn Offfall on (Cut Full Perimeter) just fine. But I cannot then turn it back to "None" without needing to re-nest it.
https://www.youtube.com/watch?v=EMrgTwzD3ts
https://www.youtube.com/watch?v=EMrgTwzD3ts
http://www.corlanecabinetry.com
Intel Core i7-5820 3.3GHz, 16GB RAM, NVidia Quadro K2200 4GB, Windows 8.1 Pro 64 bit
CS-41 4x8
CS-45 5x12
Intel Core i7-5820 3.3GHz, 16GB RAM, NVidia Quadro K2200 4GB, Windows 8.1 Pro 64 bit
CS-41 4x8
CS-45 5x12
-
- Guru Member
- Posts: 559
- Joined: Wed, May 18 2005, 6:59PM
- Company Name: CNC Automation
- Country: CANADA
- Location: St. Zotique, Québec, Canada
- Contact:
Re: Offfall setting in CN
Okay. Then it may be that the switch back to NONE is not triggering an automatic re-nest. I am sure that this should be an easy one for the Control Nesting team.
* Just wonder why you would be flipping back and forth between the setting though. (Not that you should not be able to.)
* Just wonder why you would be flipping back and forth between the setting though. (Not that you should not be able to.)
-
- eCabinets Beta Tester
- Posts: 1119
- Joined: Tue, May 10 2005, 9:36PM
- Company Name: Corlane Custom Cabinetry LLC
- Country: UNITED STATES
- Location: Carnesville, GA
- Contact:
Re: Offfall setting in CN
The reason I flip back and forth is to save expensive labels. I print the sheets including the offfall, and then turn the offfall off to print the labels, because we don't label our offfall, since we have it cut into rectangles. (Speaking of, that feature has a couple issues as well, but that will be for another post...)
http://www.corlanecabinetry.com
Intel Core i7-5820 3.3GHz, 16GB RAM, NVidia Quadro K2200 4GB, Windows 8.1 Pro 64 bit
CS-41 4x8
CS-45 5x12
Intel Core i7-5820 3.3GHz, 16GB RAM, NVidia Quadro K2200 4GB, Windows 8.1 Pro 64 bit
CS-41 4x8
CS-45 5x12