crashed profile modeler

Discuss Thermwood 3-axis Machinery, Controller, and Software.

Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Jim Bullis

Post Reply
Will Williamson
Guru Member
Posts: 449
Joined: Thu, Dec 08 2005, 6:10PM
Company Name: Williamson Finewoodwork
Country: UNITED STATES
Location: Capac MI
Contact:

crashed profile modeler

Post by Will Williamson »

HELP unable to retrieve profile modeler settings from registry
Will

http://www.willmade.com

KEG/Intel Core i 7 CPU K875 @ 2.93 GHZ/12G Ram
Dual boot XP PRO/Windows 7 Nvidia Quatro 600 1Gig Ram
Todd Miller

Re: crashed profile modeler

Post by Todd Miller »

Will Williamson wrote:HELP unable to retrieve profile modeler settings from registry
I think what happen is that you selected a default toolgroup that did not have any tools in it.

Cause:
Customer creates new Tool Group but does NOT put tools into the group. When the customer closes PM and reopens he gets an Error saying that the "Current Tool Group contains no tools. PM will revert to Default Tool Group." Then PM closes. At the point it is a continuous loop and will not allow you to enter PM .

Solution:
Close the THM software,

Start>Run>regedit>hkey local machine>software>THM>CADCUT>App-properties

Double-Click on "Tool Group", set "Value Data" to 0, Press OK.

Re-launch the THM software, go to the Profile Modeler and make sure a tool is assigned and saved to the Tool Group before closing PM.


If this does not fix the problem let me know.
Last edited by Todd Miller on Mon, Apr 07 2008, 7:44AM, edited 1 time in total.
Daniel Vonderheide
Thermwood Team
Posts: 361
Joined: Wed, May 17 2006, 11:25AM
Location: Thermwood

Re: crashed profile modeler

Post by Daniel Vonderheide »

Will,

I have sent you an email with the toolset.bin file attached. You will need to replace the original with this new file. It's stored in the "C:\profile modeler\tools\" directory. Let me know if you need anything else.
Daniel Odom
Senior Member
Posts: 204
Joined: Thu, Oct 20 2011, 12:52PM
Company Name: Carlton Kitchen and Bath
Country: UNITED STATES

Re: crashed profile modeler

Post by Daniel Odom »

I'm having this same problem, can someone send me toolset.bin?
Will Williamson
Guru Member
Posts: 449
Joined: Thu, Dec 08 2005, 6:10PM
Company Name: Williamson Finewoodwork
Country: UNITED STATES
Location: Capac MI
Contact:

Re: crashed profile modeler

Post by Will Williamson »

Call tech support and they will email right away if you need it right now.
Will

http://www.willmade.com

KEG/Intel Core i 7 CPU K875 @ 2.93 GHZ/12G Ram
Dual boot XP PRO/Windows 7 Nvidia Quatro 600 1Gig Ram
Daniel Odom
Senior Member
Posts: 204
Joined: Thu, Oct 20 2011, 12:52PM
Company Name: Carlton Kitchen and Bath
Country: UNITED STATES

Re: crashed profile modeler

Post by Daniel Odom »

Thanks I'll do that, I was hoping all I needed was a copy of a good file to get it back up. I don't really need profile modeling at the moment but it would be nice to get it fixed.
Daniel Odom
Senior Member
Posts: 204
Joined: Thu, Oct 20 2011, 12:52PM
Company Name: Carlton Kitchen and Bath
Country: UNITED STATES

Re: crashed profile modeler

Post by Daniel Odom »

Ok, a combo of repair install and the above mentioned reg-edit seemed to do the trick, thanks.
Post Reply