control nesting 5.48 update

Discuss Thermwood 3-axis Machinery, Controller, and Software.

Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Rich Kasten

Keith Neal
Junior Member
Posts: 49
Joined: Tue, Mar 03 2009, 9:30AM
Company Name: Wilbedone Inc.
Location: Cortland,NY(upstate)USA
Contact:

control nesting 5.48 update

Postby Keith Neal » Wed, Jun 03 2009, 12:37PM

I updated our control nesting and in the "load" area was a strange program was "on deck".Curious I went to check it out and it froze up our system.After rebooting I decided to clear it out and get back to work,I could not get any of our programs to load without an error message saying another operator was trying to use that function.After several reboots I went to the thermwood site and redownloaded the update this time clearing out the strange program before continuing.It works fine now.Just letting everyone else know before they get curious as I was.

User avatar
Larry Epplin
Thermwood Team
Posts: 656
Joined: Tue, May 17 2005, 12:44PM
Location: Thermwood

Re: control nesting 5.48 update

Postby Larry Epplin » Wed, Jun 03 2009, 12:48PM

The update has been fixed. Thanks for the heads up Keith.

mohan kommineni
Junior Member
Posts: 97
Joined: Fri, Mar 20 2009, 8:01AM
Company Name: ADP STORE FIXTURES
Country: AUSTRALIA
Location: PERTH-AUSTRALIA

Re: control nesting 5.48 update

Postby mohan kommineni » Mon, Jun 08 2009, 9:22PM

i have updated the CN5.48 on our cs45 but when i try to load any program which has got pocket operation the thermwood software hangs off says send error report and i have to restart the thermwood software but if i load a job with no pockets in it that is fine it nests normal howto overcome this issue

User avatar
Larry Epplin
Thermwood Team
Posts: 656
Joined: Tue, May 17 2005, 12:44PM
Location: Thermwood

Re: control nesting 5.48 update

Postby Larry Epplin » Tue, Jun 09 2009, 9:42AM

Mohan,

Please create an Export file by clicking the Export button in Control Nesting and post it. Also, please post the TWD with pockets that will not load. You will need to either ZIP the files or change the file extension to attach them.

FredHirsch
Senior Member
Posts: 167
Joined: Tue, Oct 03 2006, 6:51PM
Location: Phoenix, AZ
Contact:

Re: control nesting 5.48 update

Postby FredHirsch » Wed, Jun 10 2009, 5:26PM

Larry,
I'm getting the same error as Mohan. This is a DXF file. This file worked in previous CN 5.47.
Please see attached for export and dxf file.
Thanks,
Fred
Attachments
ControlNest5-48.zip
(387.16 KiB) Downloaded 115 times
Fred Hirsch

FredHirsch
Senior Member
Posts: 167
Joined: Tue, Oct 03 2006, 6:51PM
Location: Phoenix, AZ
Contact:

Re: control nesting 5.48 update

Postby FredHirsch » Wed, Jun 10 2009, 5:45PM

Larry/Mohan,
I figured this out. After studying the manual with the logic of the new settings.... I only had 1/2" tool setup for pocket with that material. The default "Minimum Pocket/Leftover Area" of new CN install is ".001^2" (I think that is right). Anyway it occurred to me that the machine could never hit this as I think it would require an 1/8" tool. I cranked that setting up to .1^2 and it ran the file w/out problem.
Thx
Fred
Fred Hirsch

mohan kommineni
Junior Member
Posts: 97
Joined: Fri, Mar 20 2009, 8:01AM
Company Name: ADP STORE FIXTURES
Country: AUSTRALIA
Location: PERTH-AUSTRALIA

Re: control nesting 5.48 update

Postby mohan kommineni » Wed, Jun 10 2009, 7:57PM

FredHirsch wrote:Larry/Mohan,
I figured this out. After studying the manual with the logic of the new settings.... I only had 1/2" tool setup for pocket with that material. The default "Minimum Pocket/Leftover Area" of new CN install is ".001^2" (I think that is right). Anyway it occurred to me that the machine could never hit this as I think it would require an 1/8" tool. I cranked that setting up to .1^2 and it ran the file w/out problem.
Thx
Fred


hi
fred/larry

i have seen my settings and corrected them and its working now thanks for the help


Return to “Thermwood 3-Axis Machinery”

Who is online

Users browsing this forum: No registered users and 3 guests