Flip Operations Fence
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Jim Bullis
-
- eCabinets Beta Tester
- Posts: 284
- Joined: Tue, May 10 2005, 11:35AM
- Location: Houston, Texas
-
- eCabinets Beta Tester
- Posts: 386
- Joined: Tue, May 10 2005, 5:23AM
- Location: Lancaster, NH
- Contact:
Jason,
Thanks for the update, you put a smile on my operators face
Thanks for the update, you put a smile on my operators face
Bill Rutherford
North Woods Manufacturing
Full service CNC Machining
and Edge Banding
http://www.northwoodsmanufacturing.com
North Woods Manufacturing
Full service CNC Machining
and Edge Banding
http://www.northwoodsmanufacturing.com
-
- eCabinets Beta Tester
- Posts: 979
- Joined: Thu, May 19 2005, 10:50PM
- Location: Los Alamos, CA
I am using a Busch 15HP pump. About a year ago I started using a wasteboard. It does hold the parts better. I have a 5 X 8 table. I thinned down some wood glue and brushed it on the edges and 6\" of the surface on each side(to seal from vacuum leakage). I tack on a 4 x 8 mdf wasteboard. Recently, I had to cut some 1\" MDF. Just for kicks, I layed a 2' x 2' pc. of Melamine on top of the 1' MDF. I think the vacuum held even stronger through all of this(3/4\"+1/4\"+ 1\"). Incredible holding power.
-
- eCabinets Beta Tester
- Posts: 386
- Joined: Tue, May 10 2005, 5:23AM
- Location: Lancaster, NH
- Contact:
Jason,
I see a new version of Rolling Nest is out and I do not see the change for flip ops on wasteboards listed. Was it included? If not then could you please direct me to the \"official\" complaint form??
(After all, you promised!!!!)
I see a new version of Rolling Nest is out and I do not see the change for flip ops on wasteboards listed. Was it included? If not then could you please direct me to the \"official\" complaint form??
(After all, you promised!!!!)
Bill Rutherford
North Woods Manufacturing
Full service CNC Machining
and Edge Banding
http://www.northwoodsmanufacturing.com
North Woods Manufacturing
Full service CNC Machining
and Edge Banding
http://www.northwoodsmanufacturing.com
-
- Thermwood Team
- Posts: 1721
- Joined: Tue, May 10 2005, 1:26PM
- Location: Thermwood
- Contact:
-
- Guru Member
- Posts: 559
- Joined: Wed, May 18 2005, 6:59PM
- Company Name: CNC Automation
- Country: CANADA
- Location: St. Zotique, Québec, Canada
- Contact:
Looks like Jason has some pull with the programmers! <smile>
7/05/06 - The latest version of Control Nesting is v4.94.
* KD operations not being done as drill operation in some cases (FIXED)
* Wasteboard option for flip ops in settings (ADDED)
* Ability to add a macro at header and/or footer for each sheet (ADDED)
* Changed Room# to Job name in printed sheet (ADDED)
7/05/06 - The latest version of Control Nesting is v4.94.
* KD operations not being done as drill operation in some cases (FIXED)
* Wasteboard option for flip ops in settings (ADDED)
* Ability to add a macro at header and/or footer for each sheet (ADDED)
* Changed Room# to Job name in printed sheet (ADDED)