corner cabinet shelf holes
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal
-
- Guru Member
- Posts: 309
- Joined: Sat, Feb 04 2006, 5:13PM
- Location: Hilton Head / Bluffton SC
corner cabinet shelf holes
I know from reading various posts that we've had some problems with shelf holes...this is one I ran across this morning.
For some reason it is only the right side that has the holes on the wrong side of the sheet. Dados are correct
Any help out there or is this one for the list?
Thanks
Mark
For some reason it is only the right side that has the holes on the wrong side of the sheet. Dados are correct
Any help out there or is this one for the list?
Thanks
Mark
- Attachments
-
- cornercab.jpg (78.3 KiB) Viewed 14164 times
-
- Guru Member
- Posts: 309
- Joined: Sat, Feb 04 2006, 5:13PM
- Location: Hilton Head / Bluffton SC
-
- Guru Member
- Posts: 309
- Joined: Sat, Feb 04 2006, 5:13PM
- Location: Hilton Head / Bluffton SC
-
- Wizard Member
- Posts: 5852
- Joined: Thu, Jul 28 2005, 10:18AM
- Company Name: Dan Epps
- Country: UNITED STATES
- Location: Rocky Face GA
Are you using a different material for the side--a single sided material maybe?
Did you do anything else to that side, like part editor cuts or anything?
I know the answer to both of these is probably no but I'm just grasping at straws to see if I can figure out what is happening.
Post the cabinet so I can look at it.
Did you do anything else to that side, like part editor cuts or anything?
I know the answer to both of these is probably no but I'm just grasping at straws to see if I can figure out what is happening.
Post the cabinet so I can look at it.
-
- New Member
- Posts: 19
- Joined: Wed, Nov 15 2006, 10:49AM
-
- Guru Member
- Posts: 309
- Joined: Sat, Feb 04 2006, 5:13PM
- Location: Hilton Head / Bluffton SC
Thanx Micheal...I'll keep it in mind for the next zoo keeper wanting cherry traveling cases...
Dan - you're right...no & no here is the cabinet
Dan - you're right...no & no here is the cabinet
- Attachments
-
- WDC2436.hsf
- (736.26 KiB) Downloaded 497 times
-
- Guru Member
- Posts: 309
- Joined: Sat, Feb 04 2006, 5:13PM
- Location: Hilton Head / Bluffton SC
-
- Wizard Member
- Posts: 5852
- Joined: Thu, Jul 28 2005, 10:18AM
- Company Name: Dan Epps
- Country: UNITED STATES
- Location: Rocky Face GA
You might want to send the bad cabinet to cabinets@thermwood.com so they can take a look at it to see the new face frame problem.
-
- Guru Member
- Posts: 309
- Joined: Sat, Feb 04 2006, 5:13PM
- Location: Hilton Head / Bluffton SC
Actually Dan it was the scribe on the face frames...followed your instructions - except I added my usual 1/4\" scribe to each side and the holes were still there. Went back in and took the scribe out and the holes disappeared....
why only the right side and not the left?
Any further suggestions?
Mark
why only the right side and not the left?
Any further suggestions?
Mark
-
- Guru Member
- Posts: 309
- Joined: Sat, Feb 04 2006, 5:13PM
- Location: Hilton Head / Bluffton SC