Something a little different (for me)
Moderators: Jason Susnjara, Clint Buechlein
-
- Wizard Member
- Posts: 4723
- Joined: Mon, May 09 2005, 7:33PM
- Company Name: Double E Cabinets
- Country: UNITED STATES
- Location: Amarillo, TX
Something a little different (for me)
This is a conference table I am working on.
It is actually two tables that mate together to make one large one. The customers are going to use one table for now in their small conference room then mate the tables later on in a larger room. The eCabinets drawings were very important for this job to show the customers just how crowded the room is going to be with the first table and six chairs. Here is a link to the presentation drawings.
http://www.kerryfullington.com/table
Kerry
It is actually two tables that mate together to make one large one. The customers are going to use one table for now in their small conference room then mate the tables later on in a larger room. The eCabinets drawings were very important for this job to show the customers just how crowded the room is going to be with the first table and six chairs. Here is a link to the presentation drawings.
http://www.kerryfullington.com/table
Kerry
-
- Thermwood Team
- Posts: 1721
- Joined: Tue, May 10 2005, 1:26PM
- Location: Thermwood
- Contact:
Hi Kerry,
Very impressive!!!!
Can you email me that file so I can take a look at how you built it? cabinets@thermwood.com
thanks,
Very impressive!!!!
Can you email me that file so I can take a look at how you built it? cabinets@thermwood.com
thanks,
-
- Wizard Member
- Posts: 1346
- Joined: Thu, May 19 2005, 9:45AM
- Location: Gulfport, Fl.
- Contact:
-
- Wizard Member
- Posts: 4723
- Joined: Mon, May 09 2005, 7:33PM
- Company Name: Double E Cabinets
- Country: UNITED STATES
- Location: Amarillo, TX
Mike,
Everything was done in eCabinets. Since this drawing was done just for the design presentation I just used several \"Display Cubes\" cut out and machined in the \"Part Editor\" I think it is great that eCabinets is capable of these things other than just boxes. My customers are always impressed also which is very important to me.
The presentation is done with a little feature in PhotoShop that takes My images, re-sizes them, optimizes them for the net, puts them on a web page with backgrounds all with just couple of mouse clicks. All I have to do is upload a folder to the web server.
Thanks Dan,
I don't know if I have the job yet. It will be fun to build if I get it and I am thinking about using some of the eCabinets finishing tricks to spruce this thing up.
Kerry
Everything was done in eCabinets. Since this drawing was done just for the design presentation I just used several \"Display Cubes\" cut out and machined in the \"Part Editor\" I think it is great that eCabinets is capable of these things other than just boxes. My customers are always impressed also which is very important to me.
The presentation is done with a little feature in PhotoShop that takes My images, re-sizes them, optimizes them for the net, puts them on a web page with backgrounds all with just couple of mouse clicks. All I have to do is upload a folder to the web server.
Thanks Dan,
I don't know if I have the job yet. It will be fun to build if I get it and I am thinking about using some of the eCabinets finishing tricks to spruce this thing up.
Kerry
-
- eCabinets Beta Tester
- Posts: 979
- Joined: Thu, May 19 2005, 10:50PM
- Location: Los Alamos, CA
-
- Wizard Member
- Posts: 4723
- Joined: Mon, May 09 2005, 7:33PM
- Company Name: Double E Cabinets
- Country: UNITED STATES
- Location: Amarillo, TX
Hi Brian,
I opened Alibre a couple of times but I have software burnout. I don't want to spend any time learning anything new right now. I think it can be good software but doesn't seem very intuitive on first glance. With Rhinoceros I was able to open and start drawing. (a little) With Alibre all I can do is stare at an empty page and act confused. Probably just me. Luckily since the release of Ver. 4 I can do most everything I need to do in eCabinets.
Kerry
I opened Alibre a couple of times but I have software burnout. I don't want to spend any time learning anything new right now. I think it can be good software but doesn't seem very intuitive on first glance. With Rhinoceros I was able to open and start drawing. (a little) With Alibre all I can do is stare at an empty page and act confused. Probably just me. Luckily since the release of Ver. 4 I can do most everything I need to do in eCabinets.
Kerry
-
- Wizard Member
- Posts: 1346
- Joined: Thu, May 19 2005, 9:45AM
- Location: Gulfport, Fl.
- Contact:
Re:
I agree with you on the Alibre software, I did there online demo & I'm still confusedKerry Fullington wrote:Hi Brian,
I opened Alibre a couple of times but I have software burnout. I don't want to spend any time learning anything new right now. I think it can be good software but doesn't seem very intuitive on first glance. With Rhinoceros I was able to open and start drawing. (a little) With Alibre all I can do is stare at an empty page and act confused. Probably just me. Luckily since the release of Ver. 4 I can do most everything I need to do in eCabinets.
Kerry
We love what we do, we do it well.
-
- eCabinets Beta Tester
- Posts: 1117
- Joined: Tue, May 17 2005, 9:40PM
- Location: Vista, CA, U.S.A.
- Contact:
Conference Table
Kerry,
You amaze me with what you can do with this software! Great job as usual! You are a very talented guy.
Joe
You amaze me with what you can do with this software! Great job as usual! You are a very talented guy.
Joe
-
- Wizard Member
- Posts: 4723
- Joined: Mon, May 09 2005, 7:33PM
- Company Name: Double E Cabinets
- Country: UNITED STATES
- Location: Amarillo, TX
-
- Wizard Member
- Posts: 1346
- Joined: Thu, May 19 2005, 9:45AM
- Location: Gulfport, Fl.
- Contact:
-
- eCabinets Beta Tester
- Posts: 1117
- Joined: Tue, May 17 2005, 9:40PM
- Location: Vista, CA, U.S.A.
- Contact:
Conference Table
Looks great Kerry (except for the hole and the wires as I'm sure you agree).
Joe
Joe
-
- Wizard Member
- Posts: 1346
- Joined: Thu, May 19 2005, 9:45AM
- Location: Gulfport, Fl.
- Contact:
-
- Guru Member
- Posts: 527
- Joined: Tue, May 17 2005, 1:38PM
- Company Name: Janot Interiors Ltd
- Location: Calgary, Alberta, Canada
- Contact:
Kerry,
You still have time to do woodwork, don't you?
Excellent performance! Congratulation!
You still have time to do woodwork, don't you?
Excellent performance! Congratulation!
Jean-Gabriel Voyer
Janot Interiors Ltd
www.customcabinetscalgary.com
Dell Precision PWS490, Intel Xeon CPU,3.00 GB Ram, Window XP Pro, Quadro Fx 3500
Janot Interiors Ltd
www.customcabinetscalgary.com
Dell Precision PWS490, Intel Xeon CPU,3.00 GB Ram, Window XP Pro, Quadro Fx 3500
-
- eCabinets Beta Tester
- Posts: 979
- Joined: Thu, May 19 2005, 10:50PM
- Location: Los Alamos, CA