Undercabinet Lights, frameless

Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal

Brian Shannon
eCabinets Beta Tester
Posts: 979
Joined: Thu, May 19 2005, 10:50PM
Location: Los Alamos, CA

Undercabinet Lights, frameless

Postby Brian Shannon » Wed, Mar 18 2009, 11:11AM

How are others making upper frameless cabinets to accept undercabinet "Puck" lights without using a valance? I was thinking of using a drop-in shelf @ the bottom to leave about a 1 1/2"- 2" area between it and the bottom of the cabinet. Just but spacers/cleats all around 1st. Any other ideas?


Brian

DanEpps
Wizard Member
Posts: 5852
Joined: Thu, Jul 28 2005, 10:18AM
Company Name: Dan Epps
Country: UNITED STATES
Location: Rocky Face GA

Re: Undercabinet Lights, frameless

Postby DanEpps » Wed, Mar 18 2009, 11:29AM

That sounds reasonable as long as they are not halogen lights that reach about (seems like) 20,000 degrees. LED lights would probably work well in a configuration like that.

Rick Palechuk
Wizard Member
Posts: 1896
Joined: Wed, May 18 2005, 7:54PM
Company Name: Milltech Millworks Ltd.
Country: CANADA
Location: Edmonton, Alberta
Contact:

Re: Undercabinet Lights, frameless

Postby Rick Palechuk » Wed, Mar 18 2009, 2:00PM

We do a double shelf Brian. Cut them over-size, drill and then rout a slot in the bottom one. then glue and pin them together. Finally we cut to size and edge-band. We use 10 watt halogen for these.HTH

DanEpps
Wizard Member
Posts: 5852
Joined: Thu, Jul 28 2005, 10:18AM
Company Name: Dan Epps
Country: UNITED STATES
Location: Rocky Face GA

Re: Undercabinet Lights, frameless

Postby DanEpps » Wed, Mar 18 2009, 2:51PM

Rick

Don't the halogen bulbs get super hot or have they made changes to the design? I had halogen pucks in my kitchen and they were HOT so I changed them to LEDs.

They were surface mounted and, I'm sure, well insulated on the backs but they put out a lot of heat.

Michael S Murray
eCabinets Beta Tester
Posts: 933
Joined: Tue, May 17 2005, 2:48PM
Location: Logansport, In
Contact:

Re: Undercabinet Lights, frameless

Postby Michael S Murray » Wed, Mar 18 2009, 3:02PM

we use a light rail as standard on all our kitchens. If you dont want to see it, just use a simple flat rail and then drop your doors down flush with the bottom of it. Same look as no light rail, lots less work!
Mike Murray
Versatile Cabinet & Solid Surface
mike@versatilecabinet.com
http://www.versatilecabinet.com

Brian Shannon
eCabinets Beta Tester
Posts: 979
Joined: Thu, May 19 2005, 10:50PM
Location: Los Alamos, CA

Re: Undercabinet Lights, frameless

Postby Brian Shannon » Wed, Mar 18 2009, 4:38PM

I may do that Mike since I am not going to be installing the lights and am not sure what they will use. I will just need to tell the electrician where to run the wire.

Thanks guys,


Brian

John J. Desmond
Senior Member
Posts: 242
Joined: Wed, Oct 24 2007, 9:58PM
Company Name: American Millwork Company
Country: UNITED STATES
Location: Joplin, Missouri

Re: Undercabinet Lights, frameless

Postby John J. Desmond » Wed, Mar 18 2009, 6:23PM

Brian,

You could place a box under the cabinet. Attache a false bottom with a 1" edge. It would smaller than the actual cabinet. It would be similar to having an undercabinet stereo. Won't look just like that but I think you understand. Basically a false bottome that is only the size they need to install the lights.

John Desmond

Gary Puckett
Wizard Member
Posts: 1324
Joined: Mon, May 19 2008, 1:39PM
Company Name: The Woodworkery
Location: Saint Charles, Missouri
Contact:

Re: Undercabinet Lights, frameless

Postby Gary Puckett » Wed, Mar 18 2009, 9:30PM

Brian,

Make your wall cabinet 3" taller. Then place your bottom fixed shelf 3" from the bottom. Leave the 3' cavity open in the back. ( thats where you put the puck light ) Make your door the full length of the cabinet less 1" to allow a 1/2" reveal on top and bottom .

Gary
HP Pavilion
Vista home Premium 64bit S. pack 2
AMD Phenom-X4
9850 Quad-Core Processor
6.0GB/Go Memory
1 TB/To Hard Drive
Nividia GeForce 9800 GT

Rick Palechuk
Wizard Member
Posts: 1896
Joined: Wed, May 18 2005, 7:54PM
Company Name: Milltech Millworks Ltd.
Country: CANADA
Location: Edmonton, Alberta
Contact:

Re: Under Cabinet Lights, frameless

Postby Rick Palechuk » Thu, Mar 19 2009, 1:00AM

Dan, that's why we use 10 watt bulbs. It's not my favorite way, but some clients want it like that. I prefer to do them with a light rail and valance.

Kerry Fullington
Wizard Member
Posts: 4718
Joined: Mon, May 09 2005, 7:33PM
Company Name: Double E Cabinets
Country: UNITED STATES
Location: Amarillo, TX

Re: Undercabinet Lights, frameless

Postby Kerry Fullington » Fri, Mar 20 2009, 12:53PM

Brian,

There is a new system for building cabinets that is just starting to catch on where you put a solid wood frame on the face of your cabinet boxes. This way you can adjust the size of the bottom of the frame to hide any lights etc. :wink:

Just kidding. :D

Kerry

Michael S Murray
eCabinets Beta Tester
Posts: 933
Joined: Tue, May 17 2005, 2:48PM
Location: Logansport, In
Contact:

Re: Undercabinet Lights, frameless

Postby Michael S Murray » Fri, Mar 20 2009, 1:00PM

Ive heard about that Kerry, But I dont think it will catch on, I tried it, wastes a lot of space, hardware is way to time consuming to mount and hard to adjust. ETc, so forth, and so on..... :P :P
Mike Murray
Versatile Cabinet & Solid Surface
mike@versatilecabinet.com
http://www.versatilecabinet.com

Brian Shannon
eCabinets Beta Tester
Posts: 979
Joined: Thu, May 19 2005, 10:50PM
Location: Los Alamos, CA

Re: Undercabinet Lights, frameless

Postby Brian Shannon » Fri, Mar 20 2009, 3:55PM

Very funny Kerry! I AM one of those Face Frame guys. 98 percent of my work is Face Frame but let's not go there. Now I have 2 Frameless jobs going. I wasn't going to turn them away... Even with Face Frame I would need to build a false bottom to house the "puck" lights. Just wondering how others are doing it.


Brian

Kirt F. Bowman
Junior Member
Posts: 55
Joined: Tue, Jun 27 2006, 8:01AM

Re: Undercabinet Lights, frameless

Postby Kirt F. Bowman » Tue, Mar 24 2009, 9:18AM

One method that hasn't been offered is to make the doors 2" longer on the bottom this hides the lights and creates a seamless look with very little added expense. Very high end euro companies do this as an option. the other cool thing, you don't need hardware on the upper doors. they can be grabbed easily and pulled open.

cheers

justin mason
Junior Member
Posts: 43
Joined: Fri, Jan 20 2006, 11:31PM
Company Name: IWS
Country: UNITED STATES
Location: Redmond, wa 98052

Re: Undercabinet Lights, frameless

Postby justin mason » Sat, Mar 28 2009, 10:37PM

if you decide to make the doors longer becarfull about hinge boring.
I am doing the same thing now. lower the doors and add valance behind doors and also a 1/4" skin up under to conceal any wires.
very clean look, maybe time consuming but we are used to doing lots of extra work to get finely tuned details.
hope it goes well for you.

JM
clear design


Return to “eCabinet Systems Software”

Who is online

Users browsing this forum: Bing [Bot] and 15 guests