haven't used this feature in a while but had the opportunity this last week. Problem I am having is it appears you CANNOT use a material with a larger thickness dimension then .75". I have veneered sheets that are .765" it will not even show up in page 2 of the construction settings as a usable sheet stock material... Is it me?
Thanks,
Chris
Puzzle F/Frames
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Jim Bullis
-
- Senior Member
- Posts: 113
- Joined: Fri, Jul 29 2005, 4:00PM
- Location: Helendale, CA.
-
- Wizard Member
- Posts: 4723
- Joined: Mon, May 09 2005, 7:33PM
- Company Name: Double E Cabinets
- Country: UNITED STATES
- Location: Amarillo, TX
Re: Puzzle F/Frames
Chris,
If this is on eCabinets then make sure you have selected Sheet Stock using the Material Type drop down menu on page 2 then you can select different sheets that you have in materials.
If this is on eCabinets then make sure you have selected Sheet Stock using the Material Type drop down menu on page 2 then you can select different sheets that you have in materials.
-
- Senior Member
- Posts: 113
- Joined: Fri, Jul 29 2005, 4:00PM
- Location: Helendale, CA.
Re: Puzzle F/Frames
Hey Kerry,
Yeah I know but what I noticed is that NONE of my sheet stock that is larger than .75" is in the drop down... Can you get a larger thickness that 3/4 to show up in your drop down thickness menu??
Thanks,
Chris
Yeah I know but what I noticed is that NONE of my sheet stock that is larger than .75" is in the drop down... Can you get a larger thickness that 3/4 to show up in your drop down thickness menu??
Thanks,
Chris
-
- Wizard Member
- Posts: 4723
- Joined: Mon, May 09 2005, 7:33PM
- Company Name: Double E Cabinets
- Country: UNITED STATES
- Location: Amarillo, TX
Re: Puzzle F/Frames
Yes, I just added a 1" material.
Make sure your sheet stock has the correct thickness listed in preferences.
Make sure your sheet stock has the correct thickness listed in preferences.
-
- Senior Member
- Posts: 113
- Joined: Fri, Jul 29 2005, 4:00PM
- Location: Helendale, CA.
Re: Puzzle F/Frames
well what the heck am i doing wrong? I have all my other thickness's showing up but anything over the .75 is not there!
Tried again.. Define materials, stock type sheet, name Irwin Veneer, Length & width 4x8, thickness .765", Cost 75.00, Grain Checked, single side not checked, Image Rift Red Oak... Add. All good so far. Check in FF editor not there. I also have a 1" material a 1.5" material none of which will show up... Anyway I just increased the tolerances so I could get the cut i needed but something ain't right here.
Thanks again Kerry.
Chris
Tried again.. Define materials, stock type sheet, name Irwin Veneer, Length & width 4x8, thickness .765", Cost 75.00, Grain Checked, single side not checked, Image Rift Red Oak... Add. All good so far. Check in FF editor not there. I also have a 1" material a 1.5" material none of which will show up... Anyway I just increased the tolerances so I could get the cut i needed but something ain't right here.
Thanks again Kerry.
Chris
-
- Wizard Member
- Posts: 4723
- Joined: Mon, May 09 2005, 7:33PM
- Company Name: Double E Cabinets
- Country: UNITED STATES
- Location: Amarillo, TX
Re: Puzzle F/Frames
Chris,
Make sure you are set to Inches and Decimal in Preferences. if you are set to Inches and fractions it rounds the .765" to 3/4"
I think you could also enter your material as a nominal 3/4" and then enter the actual thickness .765" when you write the TWD file to cut.
Make sure you are set to Inches and Decimal in Preferences. if you are set to Inches and fractions it rounds the .765" to 3/4"
I think you could also enter your material as a nominal 3/4" and then enter the actual thickness .765" when you write the TWD file to cut.