Angled Cabinet

Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Scott G Vaal

Post Reply
John Tortorello
New Member
Posts: 11
Joined: Fri, Dec 30 2005, 8:40AM
Company Name: Commercial Millwork Inc
Location: 221 west division streetSyracuse,NY
Contact:

Angled Cabinet

Post by John Tortorello »

Does anybody know how to create a cabinet with angled sides?

Thanks,
John
JohnLashuay
Guru Member
Posts: 645
Joined: Mon, Nov 20 2006, 3:39PM
Company Name: Rylex Custom Cabinetry-Close
Country: UNITED STATES
Location: Pine Island, New York
Contact:

Re: Angled Cabinet

Post by JohnLashuay »

Do you have a sketch of what you are looking for that you could upload?
Rylex Custom Cabinetry & Closets
http://www.rylexonline.com
Thermwood CS 43
John Tortorello
New Member
Posts: 11
Joined: Fri, Dec 30 2005, 8:40AM
Company Name: Commercial Millwork Inc
Location: 221 west division streetSyracuse,NY
Contact:

Re: Angled Cabinet

Post by John Tortorello »

See attached image

Thanks,
John
Attachments
ANGLED CABINET.PDF
(11.94 KiB) Downloaded 444 times
Kerry Fullington
Wizard Member
Posts: 4718
Joined: Mon, May 09 2005, 7:33PM
Company Name: Double E Cabinets
Country: UNITED STATES
Location: Amarillo, TX

Re: Angled Cabinet

Post by Kerry Fullington »

John,

You will need to build it from a corner cabinet. I have attached a cabinet and i can walk you through it if you need.
angle.jpg
Attachments
angle.hsf
(138.02 KiB) Downloaded 388 times
John Tortorello
New Member
Posts: 11
Joined: Fri, Dec 30 2005, 8:40AM
Company Name: Commercial Millwork Inc
Location: 221 west division streetSyracuse,NY
Contact:

Re: Angled Cabinet

Post by John Tortorello »

Kerry,
Am I looking at the front of the cabinet or the back?
If it is the back I will have issues placing molding on.
John
Kerry Fullington
Wizard Member
Posts: 4718
Joined: Mon, May 09 2005, 7:33PM
Company Name: Double E Cabinets
Country: UNITED STATES
Location: Amarillo, TX

Re: Angled Cabinet

Post by Kerry Fullington »

John,
This is a view of the front of the cabinet. You can extend the two ends in length so that you can miter them but eCabinets will not show that graphically.
angle_02.jpg
What is the issue for moldings.


Kerry
John Tortorello
New Member
Posts: 11
Joined: Fri, Dec 30 2005, 8:40AM
Company Name: Commercial Millwork Inc
Location: 221 west division streetSyracuse,NY
Contact:

Re: Angled Cabinet

Post by John Tortorello »

Kerry,
when you say extend the two ends in length, how does that translate in the software?
Is it right front, left front, right back, left back etc.
Also I take the word graphically to mean I won't see it?

Thanks,
John
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Angled Cabinet

Post by George Davidson »

Angled Cabinet
Attachments
Corner Cabinets_12-24-11.esj
(1.09 MiB) Downloaded 405 times
Corner Cabinets_12-24-11.jpg
Corner Cabinets_2_12-24-11.jpg
John Tortorello
New Member
Posts: 11
Joined: Fri, Dec 30 2005, 8:40AM
Company Name: Commercial Millwork Inc
Location: 221 west division streetSyracuse,NY
Contact:

Re: Angled Cabinet

Post by John Tortorello »

Kerry,
The cabinet you created looks good, see attached results when I put a fixed in the cabinet.

How do I get around that?

John
Attachments
Angle Test.jpg
Kerry Fullington
Wizard Member
Posts: 4718
Joined: Mon, May 09 2005, 7:33PM
Company Name: Double E Cabinets
Country: UNITED STATES
Location: Amarillo, TX

Re: Angled Cabinet

Post by Kerry Fullington »

John,
I don't get that result when I add a fixed shelf. My fixed shelf looks like the adjustable shelf I posted above.

I have to use some tricks to get the cabinet you want from the corner cabinet.
In the cabinet I posted I have turned off the left and right ends. To add shelves I must turn the ends on, add the shelves and then turn the ends back off.
You probably won't ber able to adjust any dimensions or make changes to the cabinet without turning the ends on.

We are doing some things this cabinet was not designed to do.

I haven't looked at Georges cabinets to see if he had some better ideas. When I get back to the office Friday I will play with this some more. Right now I am working on a netbook using stolen internet so it is hard to experiment.

Kerry
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Angled Cabinet

Post by George Davidson »

Angled Cabinet
Attachments
Corner Cabinet with Shelf 12-27-11.esa
(778.02 KiB) Downloaded 386 times
Corner Cabinet_1_12-27-11.jpg
Corner Cabinet_2_12-27-11.jpg
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Angled Cabinet

Post by George Davidson »

Angled Cabinet
DXF Files_Deck,Top,Shelf
I set them up in a Cad program and save the DXF File in e-Cabinets
I hope this helps you John
Attachments
Top Cut Out.jpg
DXF Files.zip
(44.21 KiB) Downloaded 369 times
DXF Files.jpg
Post Reply