cuts the wrong size
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Jim Bullis
-
- Senior Member
- Posts: 140
- Joined: Fri, May 27 2005, 8:56AM
- Company Name: Old Style Woodwork
- Country: CANADA
- Location: Southern Alberta
cuts the wrong size
Hi Everyone,
I am doing a job for a customer that has prepared the files with Aspire. The files require slots & holes cut to an exact size and I find the sizes are not coming out correctly. Interpolated holes are under size by .005" to .01" and the same with the slots. Is there a calibration I can apply to get the cuts to cut the size drawn?
I own Aspire & do the tool-paths for the file & do the Post P myself.
Any help would be appreciated.
Thanks,
Gerry
I am doing a job for a customer that has prepared the files with Aspire. The files require slots & holes cut to an exact size and I find the sizes are not coming out correctly. Interpolated holes are under size by .005" to .01" and the same with the slots. Is there a calibration I can apply to get the cuts to cut the size drawn?
I own Aspire & do the tool-paths for the file & do the Post P myself.
Any help would be appreciated.
Thanks,
Gerry
-
- Thermwood Team
- Posts: 1740
- Joined: Tue, May 17 2005, 12:44PM
- Company Name: Thermwood Corporation
- Location: Thermwood Corp: Dale, Indiana
- Contact:
Re: cuts the wrong size
Gerry,
Add a G07F5 to the beginning of your posted programs and see if your holes are then correct.
Add a G07F5 to the beginning of your posted programs and see if your holes are then correct.
Regards,
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000
-
- Senior Member
- Posts: 140
- Joined: Fri, May 27 2005, 8:56AM
- Company Name: Old Style Woodwork
- Country: CANADA
- Location: Southern Alberta
Re: cuts the wrong size
Hi Scott,
I will give that a try.
Thanks,
Gerry
I will give that a try.
Thanks,
Gerry
-
- Senior Member
- Posts: 140
- Joined: Fri, May 27 2005, 8:56AM
- Company Name: Old Style Woodwork
- Country: CANADA
- Location: Southern Alberta
Re: cuts the wrong size
Hello Scott,
I did a few test cuts
1. a interpolated hole drawn at 1.05" cuts at 1.025" with .5" cutter
2. a slot drawn at .375 wide cuts at .3615" with .25" cutter
3. a slot drawn at .25" wide cuts at .247" with .25" cutter
This is with the G07F5 in.
I have attached the NC file so you can confirm I have inserted the command properly.
Thanks,
Gerry
I did a few test cuts
1. a interpolated hole drawn at 1.05" cuts at 1.025" with .5" cutter
2. a slot drawn at .375 wide cuts at .3615" with .25" cutter
3. a slot drawn at .25" wide cuts at .247" with .25" cutter
This is with the G07F5 in.
I have attached the NC file so you can confirm I have inserted the command properly.
Thanks,
Gerry
- Attachments
-
- test slot & hole .txt
- (1.74 KiB) Downloaded 409 times
-
- Thermwood Team
- Posts: 1740
- Joined: Tue, May 17 2005, 12:44PM
- Company Name: Thermwood Corporation
- Location: Thermwood Corp: Dale, Indiana
- Contact:
Re: cuts the wrong size
Gerry,Gerry A Brown wrote:Hello Scott,
I did a few test cuts
1. a interpolated hole drawn at 1.05" cuts at 1.025" with .5" cutter
2. a slot drawn at .375 wide cuts at .3615" with .25" cutter
3. a slot drawn at .25" wide cuts at .247" with .25" cutter
This is with the G07F5 in.
I have attached the NC file so you can confirm I have inserted the command properly.
Thanks,
Gerry
Looks like your CAD/CAM is applying comp for the tooling, which is fine. However, did you actually mic your tools and see if they are under the nominal sizes? In my experience, the tools we get will not be exactly the nominal sizes. Might want to check this first. Also, are you possibly cutting too fast for the tooling and material (500ipm may be too fast for that arc radius and 3/4" material)? Also, it looks like you are doing a climb cut on the circle and the wide slot which would deflect the tool away from the finished edge. May try a conventional cut instead. If your CAD/CAM is capable, you may want to output the arc(S) as actual arc commands (G02 & G03) rather than the short G01 line commands that your program is doing (a series of short non-tangent line moves approximating the arc). G2s and G3s have automatic feed rate reduction applied based on radius and machine kinetics (but still may not reduce it enough for the tooling and material combination). By the way, the G07F5 that you have is needed and is in a good spot in your program.
Regards,
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000
Scott Vaal
-Thermwood/eCabinet Systems-
Dell Precision / Xeon E3-1240 / 8GB RAM /NVIDIA Quadro K2000
-
- Senior Member
- Posts: 140
- Joined: Fri, May 27 2005, 8:56AM
- Company Name: Old Style Woodwork
- Country: CANADA
- Location: Southern Alberta
Re: cuts the wrong size
Hi Scott,
I'll give all your suggestions a try keep you posted on the results.
Thanks,
Gerry
I'll give all your suggestions a try keep you posted on the results.
Thanks,
Gerry
-
- Guru Member
- Posts: 559
- Joined: Wed, May 18 2005, 6:59PM
- Company Name: CNC Automation
- Country: CANADA
- Location: St. Zotique, Québec, Canada
- Contact:
Re: cuts the wrong size
Scott,
If I am not mistaken, I believe that Control Nesting usually writes out NC code that turns OFF smoothing via a G07F0 call. (The default after a NC reset/HOME is G07F50 I think ??) Perhaps Gerry should try a G07F0 in place of the G07F5 suggested?
Just a thought.
If I am not mistaken, I believe that Control Nesting usually writes out NC code that turns OFF smoothing via a G07F0 call. (The default after a NC reset/HOME is G07F50 I think ??) Perhaps Gerry should try a G07F0 in place of the G07F5 suggested?
Just a thought.
-
- Senior Member
- Posts: 140
- Joined: Fri, May 27 2005, 8:56AM
- Company Name: Old Style Woodwork
- Country: CANADA
- Location: Southern Alberta
Re: cuts the wrong size
Hi,
I have been away from the shop so am a bit late responding.
Brad thanks I will try that. I have not tested any of the suggested mods yet but will post back with results when I have had a chance to do so.
Thanks,
Gerry
I have been away from the shop so am a bit late responding.
Brad thanks I will try that. I have not tested any of the suggested mods yet but will post back with results when I have had a chance to do so.
Thanks,
Gerry
-
- Senior Member
- Posts: 140
- Joined: Fri, May 27 2005, 8:56AM
- Company Name: Old Style Woodwork
- Country: CANADA
- Location: Southern Alberta
Re: cuts the wrong size
Hi,
I have worked through this trying all the suggestions. I get good results doing conventional feed with the G07F0 code. I have modified the Post P to insert this command and it all seems to work well. I have not got the Post P to output arcs yet but will pursue that as time permits.
Thanks to everyone for their help on this,
Gerry
I have worked through this trying all the suggestions. I get good results doing conventional feed with the G07F0 code. I have modified the Post P to insert this command and it all seems to work well. I have not got the Post P to output arcs yet but will pursue that as time permits.
Thanks to everyone for their help on this,
Gerry