Once in a while, we have cabinets that use a Hidden Tenon at 100% the thickness. In this case it is 1.22'' thick. When we get to the machine to machine the part with the pocket for this tenon, it searches for a tool that has the width of 1.01'' to 0.505''. We often use a half inch downcut for this procedure. I was wondering if there was a way the machine can still choose our 0.5'' inch bit and make a third pass the machine the full width?? Of course the easy solution is to buy a 5/8'' bit, but i was just wondering if there is a way not to to keep the same tool in the arm to do all of our machining without having to add another bit???
Stephane.
Tool Selection
Moderators: Jason Susnjara, Larry Epplin, Clint Buechlein, Jim Bullis
-
- New Member
- Posts: 24
- Joined: Fri, Dec 14 2012, 10:08AM
- Company Name: Aspec
- Country: CANADA
- Location: St-Odilon
-
- eCabinets Beta Tester
- Posts: 1263
- Joined: Wed, Jul 01 2009, 2:19PM
- Company Name: Halls Edge Inc
- Country: UNITED STATES
- Location: Stamford, CT USA
- Contact:
Re: Tool Selection
Hi Stephane,
Unfortunately dado operations cannot be turned into a pocket. You will have to choose a tool that is at least half the width of the dado operation. If you are machining from a .dxf file, you have the option to rename the layer "pocket" instead of "dado".
Hope this helps,
jnr
Unfortunately dado operations cannot be turned into a pocket. You will have to choose a tool that is at least half the width of the dado operation. If you are machining from a .dxf file, you have the option to rename the layer "pocket" instead of "dado".
Hope this helps,
jnr
Josh Rayburn
Hall's Edge, Inc.
CNC Machining Service
Dell Precision T3400
Win7 Professional 64 Bit/Core2Duo E8400 3ghz/4 GB Ram/NVIDIA Quadro FX570
Hall's Edge, Inc.
CNC Machining Service
Dell Precision T3400
Win7 Professional 64 Bit/Core2Duo E8400 3ghz/4 GB Ram/NVIDIA Quadro FX570
-
- Guru Member
- Posts: 559
- Joined: Wed, May 18 2005, 6:59PM
- Company Name: CNC Automation
- Country: CANADA
- Location: St. Zotique, Québec, Canada
- Contact:
Re: Tool Selection
Perhaps this is something the development team for Control Nesting should look at though...
If an operation is specified as a DADO (eCab/TWD or in a Layered DXF), yet an appropriate tool cannot be found to perform the DADO using the "Dado Operation" process, then fall back and approach the rectangular region as a POCKET.
Just a thought
If an operation is specified as a DADO (eCab/TWD or in a Layered DXF), yet an appropriate tool cannot be found to perform the DADO using the "Dado Operation" process, then fall back and approach the rectangular region as a POCKET.
Just a thought
-
- eCabinets Beta Tester
- Posts: 1263
- Joined: Wed, Jul 01 2009, 2:19PM
- Company Name: Halls Edge Inc
- Country: UNITED STATES
- Location: Stamford, CT USA
- Contact:
Re: Tool Selection
Brad,
We have been asking TWD to consider that for five years!
jnr
We have been asking TWD to consider that for five years!
jnr
Josh Rayburn
Hall's Edge, Inc.
CNC Machining Service
Dell Precision T3400
Win7 Professional 64 Bit/Core2Duo E8400 3ghz/4 GB Ram/NVIDIA Quadro FX570
Hall's Edge, Inc.
CNC Machining Service
Dell Precision T3400
Win7 Professional 64 Bit/Core2Duo E8400 3ghz/4 GB Ram/NVIDIA Quadro FX570
-
- Guru Member
- Posts: 559
- Joined: Wed, May 18 2005, 6:59PM
- Company Name: CNC Automation
- Country: CANADA
- Location: St. Zotique, Québec, Canada
- Contact:
Re: Tool Selection
Understood... Sometimes we just have to keep asking nicely.
-
- New Member
- Posts: 24
- Joined: Fri, Dec 14 2012, 10:08AM
- Company Name: Aspec
- Country: CANADA
- Location: St-Odilon
Re: Tool Selection
I agree! The fall back to a pocket would be wonderfull! Thanks