Quirk or bug

Michael Yeargain · Post by **Michael Yeargain** » Sat, Apr 28 2007, 2:20PM

Take a cabinet to the cabinet editor, remove either side, add doors and drawers (because they are removed when you remove the side) the sizes for the drawer fronts are now wrong.

Gene Kimmi · Post by **Gene Kimmi** » Sat, Apr 28 2007, 6:59PM

Mike

Look back a few pages for a post I made on doors. I am making assemblies with 3 cabinets. The middle cabinet has both sides and the right and left style deleted. When you add doors or drawer fronts to the center cabinet, 1 side will have the 1/2\" overlay and the other side of the drawer front or door is inset 1/2\".

I have not found a solution and all assemblies I build this way do this.

Michael Yeargain · Post by **Michael Yeargain** » Sat, Apr 28 2007, 7:07PM

Gene Kimmi,

I recall from memory the post you made. Are you still having problems with this?

http://www.thermwood.com/forums/viewtop ... highlight=

I didn't get back to this one as it was a stinker from what I remember. Did you find anything out?

Gene Kimmi · Post by **Gene Kimmi** » Sat, Apr 28 2007, 9:47PM

I have not gotten this resolved. Every assembly I create does this. I wonder if it is tied into the problem people are having deleting assemblies. One of the Thermwood guys worked on it and sent it back to me and I still had problems with it. I have been so busy, I haven't had time to mess with it anymore or get back to Thermwood on it.

I make all my multi-section cabinets this way because I like the styles to run from the top of the cabinet to the bottom instead of the top and bottom rails running all the way across the cabinet.

Michael Yeargain · Post by **Michael Yeargain** » Sat, Apr 28 2007, 11:04PM

I was wondering why you needed this type of cabinet set up. Now I know the rest of the story.

Justin Melhiser · Post by **Justin Melhiser** » Mon, Apr 30 2007, 8:07AM

Michael

Are you using std base framed cabinet? I would like for you to post your cabinet you are having trouble with. I will take a looka t it for you.

Thank You
Justin

Michael Yeargain · Post by **Michael Yeargain** » Mon, Apr 30 2007, 11:11PM

Frameless.

I sent you files.

Thanks

Justin Melhiser · Post by **Justin Melhiser** » Tue, May 01 2007, 9:02AM

Michael
What Version and build are you running?

Thank You
Justin

Michael Yeargain · Post by **Michael Yeargain** » Tue, May 01 2007, 8:04PM

Justin,

I am running V5.1 Bld2 on both computers. Home/work

The graphics card for the shop computer is a nVidia, Quadro FX 4500, 512MB dual VGA or DVI. Nice and Pretty pricey too.

The card for my home computer is a MSI Radeon xpress 200 series. Pretty quick for a Big Box purchase.

Thanks.

Justin Melhiser · Post by **Justin Melhiser** » Wed, May 02 2007, 7:13AM

On which cabinet, out of the ones you sent me, does the drawers change the size after removing one of the sides?

Justin Melhiser · Post by **Justin Melhiser** » Wed, May 02 2007, 7:47AM

Gene

Will you post your cabinet or send it to me. I will take a look at it for you.
My email is jdmelhis@thermwood.com. Thank you

Gene Kimmi · Post by **Gene Kimmi** » Thu, May 03 2007, 7:21PM

Justin,

Here is the assembly that I am having trouble with. I have made several other assemblies similar to this, and have the same problems with them.